Fan Parts

Home About Us Contact Us Help

Buy Online or Call 1-800-476-5888

Heaters

Exhaust Fans

Make-Up Air

Accessories » Economy Inline Filtered Modular Packaged Unit Rooftop Filtered

Cooling Modules Heating Modules Intake/Discharge Accessories

DUCTWORK

Single Wall Grease Duct Double Wall Grease Duct Chimney Special Gas Vent HVAC Supply Duct

Kitchen Ventilation

HVAC

CASLINK

Resources

DR12HTH Parts

Motors, Pulleys, & Motor Specific Parts

Motor HP Phs Voltage FLA Shaft Frame Weight RPM Vendor

CK42BS04M01-50-115 0.18 1 115 V 2.4 0.5" 9 lbs 1400 HSSA

ODP (Open Drip Proof)

Show parts

810022	Green Ground Screw
Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
58371-1/2	Junction Box - 2 1/8" X 4" X 2 1/16" - Used for mounting Speed Controls and 3 pole switches. 2-1/8" Deep.
TY-224-107-CONNECTOR	Motor Connector - Quick Disconnect Wire Harness With Ground. Used To Connect Direct Drive DU/DR Motors With Six Pin Connectors To The Speed Control. Used For 115/1/60 & 230/1/60 Vac Motors & Speed Controls.
KBWC-16K	Motor Speed Control, Solid State, Model KBWC-16K (H6323), 6 AMPS - 120 V.A.C. @25°C. Factory set to reduce to 65VAC under motor load. (72 VAC with 100 Watt load)
800023B	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.

CK42BS04M01-50-230 0.18 1 230 V 1.2 0.5" 9 lbs 1400 HSSA

ODP (Open Drip Proof)

Show parts

810022	Green Ground Screw
Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
58371-1/2	Junction Box - 2 1/8" X 4" X 2 1/16" - Used for mounting Speed Controls and 3 pole switches. 2-1/8" Deep.
TY-224-107-CONNECTOR	Motor Connector - Quick Disconnect Wire Harness With Ground. Used To Connect Direct Drive DU/DR Motors With Six Pin Connectors To The Speed Control. Used For 115/1/60 & 230/1/60 Vac Motors & Speed Controls.
KBWC-25K-H6182	Motor Speed Control, Solid State, Model KBWC-25K (H6182), 5 AMPS - 230 V.A.C. @25°C. Factory set to reduce to 130 VAC under motor load. (150 VAC with 100 Watt load). Used On DU/DR 85 HFA.
800023B	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.

CK42BS04M01-60-115 0.18 1 115 V 1.9 0.5" 10 lbs 1620 HSSA

ODP (Open Drip Proof)

Show parts

810022	Green Ground Screw
Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
58371-1/2	Junction Box - 2 1/8" X 4" X 2 1/16" - Used for mounting Speed Controls and 3 pole switches. 2-1/8" Deep.
TY-224-107-CONNECTOR	Motor Connector - Quick Disconnect Wire Harness With Ground. Used To Connect Direct Drive DU/DR Motors With Six Pin Connectors To The Speed Control. Used For 115/1/60 & 230/1/60 Vac Motors & Speed Controls.
KBWC-16K	Motor Speed Control, Solid State, Model KBWC-16K (H6323), 6 AMPS - 120 V.A.C. @25°C. Factory set to reduce to 65VAC under motor load. (72 VAC with 100 Watt load)
800023B	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.

CK42BS04M01-60-230 0.18 1 230 V 1 0.5" 9 lbs 1620 HSSA

ODP (Open Drip Proof)

Show parts

810022	Green Ground Screw
Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
58371-1/2	Junction Box - 2 1/8" X 4" X 2 1/16" - Used for mounting Speed Controls and 3 pole switches. 2-1/8" Deep.
TY-224-107-CONNECTOR	Motor Connector - Quick Disconnect Wire Harness With Ground. Used To Connect Direct Drive DU/DR Motors With Six Pin Connectors To The Speed Control. Used For 115/1/60 & 230/1/60 Vac Motors & Speed Controls.
KBWC-25K-H6182	Motor Speed Control, Solid State, Model KBWC-25K (H6182), 5 AMPS - 230 V.A.C. @25°C. Factory set to reduce to 130 VAC under motor load. (150 VAC with 100 Watt load). Used On DU/DR 85 HFA.
800023B	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.

BMN42-180I1-ES-IBA-CA-60-115 0.25 1 115 V 2.9 0.5" 42 10 lbs 1800 Telco Intercontinental Corp

TEAO-ECM (Totally Enclosed Air Over Electronically Commutated Motor)

Show parts

20AC2	Disconnect Switch - Double Pole, Single Phase, 120-277 V, 20 AMP, Switch Used For Fan Disconnect. Switch is rated for the following. Single phase 1Hp@120V, 2HP@240V.
810022	Green Ground Screw
Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
58371-1/2	Junction Box - 2 1/8" X 4" X 2 1/16" - Used for mounting Speed Controls and 3 pole switches. 2-1/8" Deep.
58-C-1	Junction Box Cover 58C30 (10004) 2 1/4" X 4 1/8" X 3/16, 24 Ga. Zinc Plated Steel (810091)
800023B	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.
ECM-Harness-T	Wiring Harness for Telco EC motors. Connects power to speed control and transformer. Used with Telco EC Motors.

BMN42-180I1-ES-IBA-CA-50-115 0.25 1 115 V 2.9 0.5" 42 10 lbs 1800 Telco Intercontinental Corp

TEAO-ECM (Totally Enclosed Air Over Electronically Commutated Motor)

Show parts

20AC2	Disconnect Switch - Double Pole, Single Phase, 120-277 V, 20 AMP, Switch Used For Fan Disconnect. Switch is rated for the following. Single phase 1Hp@120V, 2HP@240V.
810022	Green Ground Screw
Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
58371-1/2	Junction Box - 2 1/8" X 4" X 2 1/16" - Used for mounting Speed Controls and 3 pole switches. 2-1/8" Deep.
58-C-1	Junction Box Cover 58C30 (10004) 2 1/4" X 4 1/8" X 3/16, 24 Ga. Zinc Plated Steel (810091)
800023B	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.
ECM-Harness-T	Wiring Harness for Telco EC motors. Connects power to speed control and transformer. Used with Telco EC Motors.

BMN42-180I2-ES-IBA-CA-60-230/277 0.25 1 208-230-277 V 1.9-1.8-1.5 0.5" 42 10 lbs 1800 Telco Intercontinental Corp

TEAO-ECM (Totally Enclosed Air Over Electronically Commutated Motor)

Show parts

20AC2	Disconnect Switch - Double Pole, Single Phase, 120-277 V, 20 AMP, Switch Used For Fan Disconnect. Switch is rated for the following. Single phase 1Hp@120V, 2HP@240V.
810022	Green Ground Screw
Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
58371-1/2	Junction Box - 2 1/8" X 4" X 2 1/16" - Used for mounting Speed Controls and 3 pole switches. 2-1/8" Deep.
58-C-1	Junction Box Cover 58C30 (10004) 2 1/4" X 4 1/8" X 3/16, 24 Ga. Zinc Plated Steel (810091)
800023B	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.
ECM-Harness-T	Wiring Harness for Telco EC motors. Connects power to speed control and transformer. Used with Telco EC Motors.

BMN42-180I2-ES-IBA-CA-50-230/277 0.25 1 208-230-277 V 1.9-1.8-1.5 0.5" 42 10 lbs 1800 Telco Intercontinental Corp

TEAO-ECM (Totally Enclosed Air Over Electronically Commutated Motor)

Show parts

20AC2	Disconnect Switch - Double Pole, Single Phase, 120-277 V, 20 AMP, Switch Used For Fan Disconnect. Switch is rated for the following. Single phase 1Hp@120V, 2HP@240V.
810022	Green Ground Screw
Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
58371-1/2	Junction Box - 2 1/8" X 4" X 2 1/16" - Used for mounting Speed Controls and 3 pole switches. 2-1/8" Deep.
58-C-1	Junction Box Cover 58C30 (10004) 2 1/4" X 4 1/8" X 3/16, 24 Ga. Zinc Plated Steel (810091)
800023B	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.
ECM-Harness-T	Wiring Harness for Telco EC motors. Connects power to speed control and transformer. Used with Telco EC Motors.

CK42BS04M02-50-115 0.18 1 115 V 2.4 0.5" 42 9 lbs 1400 HSSA

TEFC (Totally Enclosed Fan Cooled)

Show parts

810022	Green Ground Screw
Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
58371-1/2	Junction Box - 2 1/8" X 4" X 2 1/16" - Used for mounting Speed Controls and 3 pole switches. 2-1/8" Deep.
TY-224-107-CONNECTOR	Motor Connector - Quick Disconnect Wire Harness With Ground. Used To Connect Direct Drive DU/DR Motors With Six Pin Connectors To The Speed Control. Used For 115/1/60 & 230/1/60 Vac Motors & Speed Controls.
KBWC-16K	Motor Speed Control, Solid State, Model KBWC-16K (H6323), 6 AMPS - 120 V.A.C. @25°C. Factory set to reduce to 65VAC under motor load. (72 VAC with 100 Watt load)
800023B	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.

CK42BS04M02-50-230 0.18 1 230 V 1.2 0.5" 42 9 lbs 1400 HSSA

TEFC (Totally Enclosed Fan Cooled)

Show parts

810022	Green Ground Screw
Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
58371-1/2	Junction Box - 2 1/8" X 4" X 2 1/16" - Used for mounting Speed Controls and 3 pole switches. 2-1/8" Deep.
TY-224-107-CONNECTOR	Motor Connector - Quick Disconnect Wire Harness With Ground. Used To Connect Direct Drive DU/DR Motors With Six Pin Connectors To The Speed Control. Used For 115/1/60 & 230/1/60 Vac Motors & Speed Controls.
KBWC-25K-H6182	Motor Speed Control, Solid State, Model KBWC-25K (H6182), 5 AMPS - 230 V.A.C. @25°C. Factory set to reduce to 130 VAC under motor load. (150 VAC with 100 Watt load). Used On DU/DR 85 HFA.
800023B	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.

CK42BS04M02-60-115 0.18 1 115 V 1.9 0.5" 42 9 lbs 1625 HSSA

TEFC (Totally Enclosed Fan Cooled)

Show parts

810022	Green Ground Screw
Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
58371-1/2	Junction Box - 2 1/8" X 4" X 2 1/16" - Used for mounting Speed Controls and 3 pole switches. 2-1/8" Deep.
TY-224-107-CONNECTOR	Motor Connector - Quick Disconnect Wire Harness With Ground. Used To Connect Direct Drive DU/DR Motors With Six Pin Connectors To The Speed Control. Used For 115/1/60 & 230/1/60 Vac Motors & Speed Controls.
KBWC-16K	Motor Speed Control, Solid State, Model KBWC-16K (H6323), 6 AMPS - 120 V.A.C. @25°C. Factory set to reduce to 65VAC under motor load. (72 VAC with 100 Watt load)
800023B	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.

CK42BS04M02-60-230 0.18 1 230 V 1 0.5" 42 9 lbs 1625 HSSA

TEFC (Totally Enclosed Fan Cooled)

Show parts

810022	Green Ground Screw
Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
58371-1/2	Junction Box - 2 1/8" X 4" X 2 1/16" - Used for mounting Speed Controls and 3 pole switches. 2-1/8" Deep.
TY-224-107-CONNECTOR	Motor Connector - Quick Disconnect Wire Harness With Ground. Used To Connect Direct Drive DU/DR Motors With Six Pin Connectors To The Speed Control. Used For 115/1/60 & 230/1/60 Vac Motors & Speed Controls.
KBWC-25K-H6182	Motor Speed Control, Solid State, Model KBWC-25K (H6182), 5 AMPS - 230 V.A.C. @25°C. Factory set to reduce to 130 VAC under motor load. (150 VAC with 100 Watt load). Used On DU/DR 85 HFA.
800023B	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.

The manufacturer reserves the right to use alternate motors from alternate vendors that meet the operating requirements of the fan but may have slightly different specifications.

Replacement Parts

Part
800034 [4 used]	A0005690 - Nut Whiz 1/4-20, SFLN1420LZ, Steel, Large Flange
0120763.0800 [4 used]	A0031100 - 1"L, 1/4-20 Matpoint, Self Aligning, Hex Head, Grade 5 Bolt
F5021416 [1 used]	Baffle 8 1/4" Dia. Out. Venturi X 3 5/16" Height, .064 x 19.5" 1100-0 Alum. (Spun) (620323)
F8041516-S [1 used]	Base Assembly For DU12 / DR12
F2361516 [1 used]	Bird Screen - 1/2" X 1/2" (3 3/4" X 46") Wire Screen for Direct Drive Upblast/Downblast Fans (850030) DU/DR12, Galv after welded wire cloth.
800048 [4 used]	Bolt Whiz 1/4-20 X 1/2, Steel
800041 [4 used]	Bolt Whiz 10-32 X 1/2, SFB103212Z, Steel Grade 5 Minimum (3 Evenly Spaced Radial Marks)
LT 1/2 Conduit [1 used]	Conduit 1/2" Flexible - Non Metallic Gray, For Use With Non Metallic Liquid Tight Connectors.
F5211416 [1 used]	Hood Apron For DR12FA / DR12 / DR12RA (Spun) (620324) .064 x 28" 1100-0 Alum.
ETL-Label [1 used]	Label - ETL Information Label. Label located in job docs should be printed and shipped.
MANUAL EXHAUST [1 used]	Manual for PRVs
800030 [4 used]	Nut Whiz 10-32, SFLN1032Z, Steel, Large Flange
800036 [8 used]	Nut Whiz 8-32, Steel
800023B [4 used]	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.
SKID-3237 [1 used]	Skid - 32" X 37" - Used For BDU 11, BDCR 7, 8, 9 & 11, DU/DR 25, 30 & 33.
F2200006 [4 used]	Standoff Hex Head MF 1/4-20 4625.2520A 1/2" Dia. I.D. Hex, Zinc Plated Steel
F5041516-S [1 used]	TOP PLATE, 20GA GALVANIZED, DU/DR 12 F5041516
F8031516-S [4 used]	Vertical Brace Assy. 1" X 7 15/16", 14 Ga. Galv. Steel For DU12 / DR12
800011 [4 used]	Washer 1/4 Dia. Ins. X 5/8 Dia. Out. X 1/16 Thk., Steel - 360 PER lbs.
800014 [4 used]	Washer Nylon 1/4 Dia. Ins. X 9/16 Dia. Out. X 1/16 Thk., Nylon (Color White)
F8011516 [1 used]	Wheel Assembly 10 1/2" Dia. Top X 8 1/2" Dia. Ins. Bottom X 4 3/16" Height used on DU, DR 12 DD (620319).

Curbs

Part
CRB17.5X8E	ROOF CURB - 17.5" Square X 8" High
CRB17.5X9E	ROOF CURB - 17.5" Square X 9" High
CRB17.5X12E	ROOF CURB - 17.5" Square X 12" High
CRB17.5X12-BTC	BOLT TOGETHER ROOF CURB - 17.5" Square X 12" High, 18 GA Galvanized. Ships Flat. Pitched Curb Option Not Available with Bolt Together Curbs.
CRB17.5X14E	ROOF CURB - 17.5" Square X 14" High
CRB17.5X16E	Roof Curb 17-1/2" sq. x 16" high
CRB17.5X18E	Roof Curb 17-1/2" sq. x 18" high
CRB17.50X20E	ROOF CURB - 17.50" Square X 20" High
CRB17.5X20E	Roof Curb 17-1/2" sq. x 20" high
CRB17.50X21E	ROOF CURB - 17.50" Square X 21" High
CRB17.5x22E	ROOF CURB - 17.5" Square X 22" High
CRB17.5x24E	ROOF CURB - 17.5" Square X 24" High
CRB17.5x26E	ROOF CURB - 17.5" Square X 26" High
CRB17.5x26L-BTC	BOLT TOGETHER ROOF CURB - 17.5" Square X 26" High, 18 GA Galvanized. Vented. Ships Flat. Pitched Curb Option Not Available with Bolt Together Curbs.
CRB17.5x52E	Roof Curb 17-1/2" sq. x 52" high
CRB17.5x55E	Roof Curb 17-1/2" sq. x 55" high
CRB17.5x61E	Roof Curb 17-1/2" sq. x 61" high

Options

Part
ECM Wiring Package - MSC	ECM Wiring Package - Exhaust - Manual or 0-10VDC Reference Speed Control -MSC- (TELCO), CCW Rotation
Show parts
	CAS MSC [1 used]	Motor Speed Control for EC motors. For use with Nidec and Telco EC motors. Uses 0 to 100% or 0 to 10V speed reference with rpm indication. 24VAC/24VDC input. Controls 4 Pole/1800 RPM motor with PWM input. Includes 0-10VDC input speed reference pins. Part replaces: ECM-VCU-RTC. Controller needs initial programming before shipping from the factory.
MSC w/ 10KLVC-DB	ECM Wiring Package - Exhaust - Manual Potentiometer Speed Control -MSC-
Show parts
	10KLVC-DB [1 used]	10K OHM POTENTIOMETER WITH INTEGRATED WALL PLATE.
	CAS MSC [1 used]	Motor Speed Control for EC motors. For use with Nidec and Telco EC motors. Uses 0 to 100% or 0 to 10V speed reference with rpm indication. 24VAC/24VDC input. Controls 4 Pole/1800 RPM motor with PWM input. Includes 0-10VDC input speed reference pins. Part replaces: ECM-VCU-RTC. Controller needs initial programming before shipping from the factory.
ECM Wiring Package-RTC	ECM Wiring Package - Manual or 0-10VDC Reference Speed Control -RTC- (TELCO Motor), CCW Rotation
Show parts
	ECM-VCU-RTC [1 used]	Motor Speed Control for EC motors. For use with Nidec and Telco EC motors. Uses 0 to 100% speed reference with rpm indication. 24VAC input. Controls 4 Pole/1800 RPM motor with PWM input. Includes 0-10VDC input speed reference pins. Part replaces EVO/ECM-VCU-36-MP and EVO/ECM-ACU+S1.1-MP.
I 12 BDD w/ 120/240V Motor	MOTORIZED BACK DRAFT DAMPER - with flange, damper is 12" sq. 2" deep, O.D. of flange is 14" sq. Actuator is 120/240V
Show parts
	MTR-611 [1 used]	120/240 v Motor Pack for I Series Backdraft Dampers
	I 12 BDD [1 used]	Gravity Back Draft Damper - with flange, damper is 12" sq. 2" deep, O.D. of flange is 14" sq.
I 12 BDD w/ 24V Motor	MOTORIZED BACK DRAFT DAMPER - with flange, damper is 12" sq. 2" deep, O.D. of flange is 14" sq. Actuator is 24V
Show parts
	MTR-611 24V [1 used]	24 V Motor Pack for I Series Backdraft Dampers
	I 12 BDD [1 used]	Gravity Back Draft Damper - with flange, damper is 12" sq. 2" deep, O.D. of flange is 14" sq.
WALLMOUNT 18.5"SQ x 2"	Wall Mount Bracket - 18.5" square x 2" for fans with 19" square base and with 13" centered square hole.
WALLMOUNT 18.5"SQ x 5"	Wall Mount Bracket - 18.5" square x 5" for fans with 19" square base, with 13" centered square hole. Used when gravity damper is ordered.
FAN HEAT BAFFLE	Insulated Heat Baffle for Exhaust Fans. Type 475FRK 1 inch thick insulation installed on the top side of the top plate and under the motor of upblast and downblast fans. Cut to fit shaft wrapper and around vibration isolators and motor cooling hole. Caulked down to top plate.
Show parts
	INSULATION/sq ft [3 used]	INSULATION (Price per Sq Foot)
EYEBOLTS-4	Eye Bolt 4 - Eye Bolts Are Installed On The Outside Of The Apron / Hood. Used For Guy Line Tie Off On Fans With 4 Tie Off Points.
Show parts
	9489T170 [4 used]	Eye Bolt - Light Duty With Nut, Zinc Plated, 1/4-20 x 7/8" Threads - 1" Shank.
	800031 [4 used]	Nut Nylon Insert 1/4-20, NILN 1420Z, Steel With White Nylon Insert
	800011 [8 used]	Washer 1/4 Dia. Ins. X 5/8 Dia. Out. X 1/16 Thk., Steel - 360 PER lbs.
HBKIT-01	HINGE KIT - Standard Hinge kit for exhaust fan roof curbs. Includes Hardware to attach hinge to curb and hinge to base. Ships Loose. Used on Fans with wheels 20 inches or smaller. 12 GA Galvanized.
Show parts
	800032 [6 used]	A0005688 - Zinc-Plated Grade 5 Steel Serrated-Flange Locknut, 3/8"-16 Thread Size, 7/8" Large Flange Diameter, 11/32" Overall Height
	31817 [30 used]	Self Drilling Screw - 12 - 14 X 3/4" - Steel, Zinc Coated - Used To Mount Hinge Kits.
MIAMI-DADE NOA-1 Aluminum Downblast 10	Miami Dade Impact and Wind Load Certification +150 / -150 PSF - Miami Dade County Product Control Approved. Florida Building Code approval. Downblast size 10. Roof & Wall Mount Exhaust Curbs up to 20" high must be 20 gauge Aluminized. Roof & Wall Mount Exhaust Curbs above 20" high up to 42" high must be 18 Gauge Aluminized.
Show parts
	F237DB10 [1 used]	Angle Ring 1/8" X 1" X 1" Aluminum Angle, 23.750" Dia. Out. For DR12
	800023B [6 used]	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.
2E340	Line Voltage Thermostat, 120 or 240 volt, used as fan thermostat in cooling applications. Close on temperature rise. 80-130 degree dial. 2E340. 13.8 amps at 120V, 10 amps at 240V.
Through Wall Curb Mount	Through Wall Curb Mount Installation Option.
I 12 BDD	Gravity Back Draft Damper - with flange, damper is 12" sq. 2" deep, O.D. of flange is 14" sq.
Full Crating for Exhaust Fan	Full crating for exhaust fans for shipping.
EPO11-Enamel	Tan Enamel Coating For 11" or smaller Fan. Consult factory for other colors. Sherwin Williams p/n F75KXN5809-4347, (AX = A0006229) Color: SW2353. Adds two weeks to the lead time of unit.
MS100W	Occupancy Sensor, White, 120VAC. 1/2HP, 9 Amp Max (Fan +Light). 300W max LED, 600W max Incandescent. Fits single-gang box.

Security Policy		Privacy Policy		Legal Notice		Warranty		Return Policy
Copyright ® 2003-2014 Thermotek All Rights Reserved.