Fan Parts

Home About Us Contact Us Help

Buy Online or Call 1-800-476-5888

Heaters

Exhaust Fans

Make-Up Air

Accessories » Economy Inline Filtered Modular Packaged Unit Rooftop Filtered

Cooling Modules Heating Modules Intake/Discharge Accessories

DUCTWORK

Single Wall Grease Duct Double Wall Grease Duct Chimney Special Gas Vent HVAC Supply Duct

Kitchen Ventilation

HVAC

CASLINK

Resources

TH-SIF10DD Parts

Motors, Pulleys, & Motor Specific Parts

Motor HP Phs Voltage FLA Shaft Frame Weight RPM Vendor

CK42BS04M01-50-115 0.18 1 115 V 2.4 0.5" 9 lbs 1400 HSSA

ODP (Open Drip Proof)

Show parts

Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
TY-224-107-CONNECTOR	Motor Connector - Quick Disconnect Wire Harness With Ground. Used To Connect Direct Drive DU/DR Motors With Six Pin Connectors To The Speed Control. Used For 115/1/60 & 230/1/60 Vac Motors & Speed Controls.
KBWC-16K	Motor Speed Control, Solid State, Model KBWC-16K (H6323), 6 AMPS - 120 V.A.C. @25°C. Factory set to reduce to 65VAC under motor load. (72 VAC with 100 Watt load)
800030	Nut Whiz 10-32, SFLN1032Z, Steel, Large Flange

CK42BS04M01-50-230 0.18 1 230 V 1.2 0.5" 9 lbs 1400 HSSA

ODP (Open Drip Proof)

Show parts

Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
TY-224-107-CONNECTOR	Motor Connector - Quick Disconnect Wire Harness With Ground. Used To Connect Direct Drive DU/DR Motors With Six Pin Connectors To The Speed Control. Used For 115/1/60 & 230/1/60 Vac Motors & Speed Controls.
KBWC-25K-H6182	Motor Speed Control, Solid State, Model KBWC-25K (H6182), 5 AMPS - 230 V.A.C. @25°C. Factory set to reduce to 130 VAC under motor load. (150 VAC with 100 Watt load). Used On DU/DR 85 HFA.
800030	Nut Whiz 10-32, SFLN1032Z, Steel, Large Flange

CK42BS04M01-60-115 0.18 1 115 V 1.9 0.5" 10 lbs 1620 HSSA

ODP (Open Drip Proof)

Show parts

Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
TY-224-107-CONNECTOR	Motor Connector - Quick Disconnect Wire Harness With Ground. Used To Connect Direct Drive DU/DR Motors With Six Pin Connectors To The Speed Control. Used For 115/1/60 & 230/1/60 Vac Motors & Speed Controls.
KBWC-16K	Motor Speed Control, Solid State, Model KBWC-16K (H6323), 6 AMPS - 120 V.A.C. @25°C. Factory set to reduce to 65VAC under motor load. (72 VAC with 100 Watt load)
800030	Nut Whiz 10-32, SFLN1032Z, Steel, Large Flange

CK42BS04M01-60-230 0.18 1 230 V 1 0.5" 9 lbs 1620 HSSA

ODP (Open Drip Proof)

Show parts

Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
TY-224-107-CONNECTOR	Motor Connector - Quick Disconnect Wire Harness With Ground. Used To Connect Direct Drive DU/DR Motors With Six Pin Connectors To The Speed Control. Used For 115/1/60 & 230/1/60 Vac Motors & Speed Controls.
KBWC-23K-H6180	Motor Speed Control, Solid State, Model KBWC-23K (H6180), 2.5 AMPS - 230 V.A.C. @25°C. Factory set to reduce to 130 VAC under motor load. (172 VAC with 100 Watt load). Used On DU/DR30 HFA
800030	Nut Whiz 10-32, SFLN1032Z, Steel, Large Flange

BMN42-180I1-ES-IBA-CA-60-115 0.25 1 115 V 2.9 0.5" 42 10 lbs 1800 Telco Intercontinental Corp

TEAO-ECM (Totally Enclosed Air Over Electronically Commutated Motor)

Show parts

Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
SIF910DDMTRCVRTRANS	Motor Cover Transformer Cover for direct drive Square Inline Fan with 9-10" wheel.
800030	Nut Whiz 10-32, SFLN1032Z, Steel, Large Flange
800023B	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.
ECM-Harness-T	Wiring Harness for Telco EC motors. Connects power to speed control and transformer. Used with Telco EC Motors.

BMN42-180I1-ES-IBA-CA-50-115 0.25 1 115 V 2.9 0.5" 42 10 lbs 1800 Telco Intercontinental Corp

TEAO-ECM (Totally Enclosed Air Over Electronically Commutated Motor)

Show parts

Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
SIF910DDMTRCVRTRANS	Motor Cover Transformer Cover for direct drive Square Inline Fan with 9-10" wheel.
800030	Nut Whiz 10-32, SFLN1032Z, Steel, Large Flange
800023B	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.
ECM-Harness-T	Wiring Harness for Telco EC motors. Connects power to speed control and transformer. Used with Telco EC Motors.

BMN42-180I2-ES-IBA-CA-60-230/277 0.25 1 208-230-277 V 1.9-1.8-1.5 0.5" 42 10 lbs 1800 Telco Intercontinental Corp

TEAO-ECM (Totally Enclosed Air Over Electronically Commutated Motor)

Show parts

Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
SIF910DDMTRCVRTRANS	Motor Cover Transformer Cover for direct drive Square Inline Fan with 9-10" wheel.
800030	Nut Whiz 10-32, SFLN1032Z, Steel, Large Flange
800023B	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.
ECM-Harness-T	Wiring Harness for Telco EC motors. Connects power to speed control and transformer. Used with Telco EC Motors.

BMN42-180I2-ES-IBA-CA-50-230/277 0.25 1 208-230-277 V 1.9-1.8-1.5 0.5" 42 10 lbs 1800 Telco Intercontinental Corp

TEAO-ECM (Totally Enclosed Air Over Electronically Commutated Motor)

Show parts

Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
SIF910DDMTRCVRTRANS	Motor Cover Transformer Cover for direct drive Square Inline Fan with 9-10" wheel.
800030	Nut Whiz 10-32, SFLN1032Z, Steel, Large Flange
800023B	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.
ECM-Harness-T	Wiring Harness for Telco EC motors. Connects power to speed control and transformer. Used with Telco EC Motors.

The manufacturer reserves the right to use alternate motors from alternate vendors that meet the operating requirements of the fan but may have slightly different specifications.

Replacement Parts

Part
800032 [4 used]	A0005688 - Zinc-Plated Grade 5 Steel Serrated-Flange Locknut, 3/8"-16 Thread Size, 7/8" Large Flange Diameter, 11/32" Overall Height
800034 [4 used]	A0005690 - Nut Whiz 1/4-20, SFLN1420LZ, Steel, Large Flange
0120763.0800 [20 used]	A0031100 - 1"L, 1/4-20 Matpoint, Self Aligning, Hex Head, Grade 5 Bolt
SIF910ADR [2 used]	Access Door for Square Inline Fan with 9-10" wheel.
SIF910DDBASE [2 used]	Base for Square Inline Fan with 9-10" wheel.
92323A558 [4 used]	Bolt Whiz 3/8-16 X 1 1/2, Steel Grade 5 Minimum (3 Evenly Spaced Radial Marks)
11626-03224 [1 used]	Cage Nut - 1/4" - 20. Installed in 1/2" square hole. Used on 20 gauge material.
SIF910CP [2 used]	Corner Post for Square Inline Fan with 9-10" wheel.
SIF910CPOR [1 used]	Corner Post Opposite Rear for Square Inline Fan with 9-10" wheel.
SIF910CPR [1 used]	Corner Post Rear for Square Inline Fan with 9-10" wheel.
SIF910CRNRS [4 used]	Corner Support for wall/ ceiling mounting Square Inline Fan Sizes 9-10.
SIF910FIP [1 used]	Front Inlet Panel for Square Inline Fan with 9-10" wheel.
8012A [2 used]	J-BOX - SWITCH BOX - CY X 1/2.
58-C-1 [1 used]	Junction Box Cover 58C30 (10004) 2 1/4" X 4 1/8" X 3/16, 24 Ga. Zinc Plated Steel (810091)
SIF910DDMTRCVR [1 used]	Motor Cover for direct drive Square Inline Fan with 9-10" wheel.
SIF910DDMTRPLT [1 used]	Motor Plate for direct drive Square Inline Fan with 9-10" wheel.
SIF910DDMTRPLTSUP [1 used]	Motor Plate Support for direct drive Square Inline Fan with 9-10" wheel.
F5020010-SIF10DD [1 used]	Venturi 13.500" OD X 1 5/8" Height, .064" 1100-0 Alum. Used on SIF10DD.
F8011516 [1 used]	Wheel Assembly 10 1/2" Dia. Top X 8 1/2" Dia. Ins. Bottom X 4 3/16" Height used on DU, DR 12 DD (620319).

Options

Part
ECM Wiring Package - MSC	ECM Wiring Package - Exhaust - Manual or 0-10VDC Reference Speed Control -MSC- (TELCO), CCW Rotation
Show parts
	CAS MSC [1 used]	Motor Speed Control for EC motors. For use with Nidec and Telco EC motors. Uses 0 to 100% or 0 to 10V speed reference with rpm indication. 24VAC/24VDC input. Controls 4 Pole/1800 RPM motor with PWM input. Includes 0-10VDC input speed reference pins. Part replaces: ECM-VCU-RTC. Controller needs initial programming before shipping from the factory.
MSC w/ 10KLVC-DB	ECM Wiring Package - Exhaust - Manual Potentiometer Speed Control -MSC-
Show parts
	10KLVC-DB [1 used]	10K OHM POTENTIOMETER WITH INTEGRATED WALL PLATE.
	CAS MSC [1 used]	Motor Speed Control for EC motors. For use with Nidec and Telco EC motors. Uses 0 to 100% or 0 to 10V speed reference with rpm indication. 24VAC/24VDC input. Controls 4 Pole/1800 RPM motor with PWM input. Includes 0-10VDC input speed reference pins. Part replaces: ECM-VCU-RTC. Controller needs initial programming before shipping from the factory.
ECM Wiring Package - MSC - MODBUS	ECM Wiring Package - Exhaust - MODBUS Control -MSC- (TELCO), CCW Rotation
Show parts
	CAS MSC [1 used]	Motor Speed Control for EC motors. For use with Nidec and Telco EC motors. Uses 0 to 100% or 0 to 10V speed reference with rpm indication. 24VAC/24VDC input. Controls 4 Pole/1800 RPM motor with PWM input. Includes 0-10VDC input speed reference pins. Part replaces: ECM-VCU-RTC. Controller needs initial programming before shipping from the factory.
ECM Wiring Package-RTC	ECM Wiring Package - Manual or 0-10VDC Reference Speed Control -RTC- (TELCO Motor), CCW Rotation
Show parts
	ECM-VCU-RTC [1 used]	Motor Speed Control for EC motors. For use with Nidec and Telco EC motors. Uses 0 to 100% speed reference with rpm indication. 24VAC input. Controls 4 Pole/1800 RPM motor with PWM input. Includes 0-10VDC input speed reference pins. Part replaces EVO/ECM-VCU-36-MP and EVO/ECM-ACU+S1.1-MP.
ECM Wiring Package-ECPM03	ECM Wiring Package - PWM Signal from ECPMO3 Prewire (TELCO Motor), CCW Rotation
I 12 BDD w/ 120/240V Motor	MOTORIZED BACK DRAFT DAMPER - with flange, damper is 12" sq. 2" deep, O.D. of flange is 14" sq. Actuator is 120/240V
Show parts
	MTR-611 [1 used]	120/240 v Motor Pack for I Series Backdraft Dampers
	I 12 BDD [1 used]	Gravity Back Draft Damper - with flange, damper is 12" sq. 2" deep, O.D. of flange is 14" sq.
I 12 BDD w/ 24V Motor	MOTORIZED BACK DRAFT DAMPER - with flange, damper is 12" sq. 2" deep, O.D. of flange is 14" sq. Actuator is 24V
Show parts
	MTR-611 24V [1 used]	24 V Motor Pack for I Series Backdraft Dampers
	I 12 BDD [1 used]	Gravity Back Draft Damper - with flange, damper is 12" sq. 2" deep, O.D. of flange is 14" sq.
HSA75-4	Hanging Vibration Isolators for Square Inline Fans. Contains four HSA75 Hanging Isolators.
Show parts
	HSA75 [4 used]	Isolation spring with 75lbs resistance, 1.50" rated deflection, for hanging installation. Color, Orange.
2E340	Line Voltage Thermostat, 120 or 240 volt, used as fan thermostat in cooling applications. Close on temperature rise. 80-130 degree dial. 2E340. 13.8 amps at 120V, 10 amps at 240V.
I 12 BDD	Gravity Back Draft Damper - with flange, damper is 12" sq. 2" deep, O.D. of flange is 14" sq.
Dry Mode Exhaust	Current Sensor Mounted In Exhaust Fan For Use With Pool Room Temp Control
Show parts
	A/MCS-A [1 used]	Current Sensor - Solid Core, AC Current Range: 0.32 - 150A , NO Contact w/ Max Rating of 1A @ 36VAC/VDC
Full Crating for Exhaust Fan	Full crating for exhaust fans for shipping.
EPO910-SIF-Enamel	Tan Enamel Coating For 9/10" SIF Fan. Consult factory for other colors. Sherwin Williams p/n F75KXN5809-4347, (AX = A0006229) Color: SW2353. Adds two weeks to the lead time of unit.
SIF910SD-Left-Square	Side Discharge door for SIF 9-10. Left side from inlet. Square Duct Connection.
SIF910SD-Left-DW10FRISER	Side Discharge door for SIF 9-10. Left side from inlet. Standard 10" Duct Connection.
Show parts
	800034 [8 used]	A0005690 - Nut Whiz 1/4-20, SFLN1420LZ, Steel, Large Flange
	0120763.0800 [8 used]	A0031100 - 1"L, 1/4-20 Matpoint, Self Aligning, Hex Head, Grade 5 Bolt
	SIF910DA [1 used]	Discharge Adapter used to go from SIF9-10 to round duct.
SIF910SD-Right-Square	Side Discharge door for SIF 9-10. Right side from inlet. Square Duct Connection.
SIF910SD-Right-DW10FRISER	Side Discharge door for SIF 9-10. Right side from inlet. Standard 10" Duct Connection.
Show parts
	800034 [8 used]	A0005690 - Nut Whiz 1/4-20, SFLN1420LZ, Steel, Large Flange
	0120763.0800 [8 used]	A0031100 - 1"L, 1/4-20 Matpoint, Self Aligning, Hex Head, Grade 5 Bolt
	SIF910DA [1 used]	Discharge Adapter used to go from SIF9-10 to round duct.
SIF910SD-Straight-Square	SIF9-10 with straight discharge. Square Duct Connection.
SIF910SD-Straight-DW10FRISER	SIF9-10 with straight discharge. Standard 10" Duct Connection.
Show parts
	800034 [8 used]	A0005690 - Nut Whiz 1/4-20, SFLN1420LZ, Steel, Large Flange
	0120763.0800 [8 used]	A0031100 - 1"L, 1/4-20 Matpoint, Self Aligning, Hex Head, Grade 5 Bolt
	SIF910DA [1 used]	Discharge Adapter used to go from SIF9-10 to round duct.
SIF910DSO	Intake/Discharge Screen Option used on the SIF9-10.
Show parts
	SIF910DS [1 used]	Discharge Screen used on the SIF9-10.
SIF910DSO	Intake/Discharge Screen Option used on the SIF9-10.
Show parts
	SIF910DS [1 used]	Discharge Screen used on the SIF9-10.
SIF 910 - Filter Box - 2 inch Merv 13 Filter	SIF 9-10 - Filter Box with 2 inch Merv 13 Filter
Show parts
	SIF910FB2INF [2 used]	2 Inch Filter Rack for Square Inline 9 & 10 Fan Filter Bank
	800032 [8 used]	A0005688 - Zinc-Plated Grade 5 Steel Serrated-Flange Locknut, 3/8"-16 Thread Size, 7/8" Large Flange Diameter, 11/32" Overall Height
	0120763.0800 [8 used]	A0031100 - 1"L, 1/4-20 Matpoint, Self Aligning, Hex Head, Grade 5 Bolt
	SIF910FBBP [2 used]	Back Post for Square Inline 9-10 Fan Filter Box
	SIF910FBB [1 used]	Base for Square Inline 9-10 Fan Filter Bank
	11626-03224 [8 used]	Cage Nut - 1/4" - 20. Installed in 1/2" square hole. Used on 20 gauge material.
	SIF910FBBRACKET [8 used]	Connecting Bracket for Square Inline 9-10 Fan Filter Bank
	SIF910FBFRBC [4 used]	Cover for the Filter Rack Blank for Square Inline 9-10 Fan Filter Bank
	SIF910FBD [2 used]	Door for Square Inline 9-10 Fan Filter Bank
	SIF910FBDL [2 used]	Door Liner for Square Inline 9-10 Fan Filter Bank
	SIF910FBFRB [2 used]	Filter Rack Back for Square Inline 9-10 Fan Filter Bank
	SIF910FBFR [2 used]	Filter Rack for Square Inline 9-10 Fan Filter Bank
	SIF910FBFP [2 used]	Front Post for Square Inline 9-10 Fan Filter Box
	SB6-4-RIVET [94 used]	RIVET - 3/16" Diameter, .126 To .250 Grip Range, SB6-4 Button Head Steel/Steel. Replaced 800075.
	MERV 13 16X16X2 [1 used]	Throw away filter 16wx16hx2d, MERV13 rating.
	SIF910FBT [1 used]	Top for Square Inline 9-10 Fan Filter Bank
	11104711 [8 used]	Zinc-Plated Grade 5 Steel Serrated-Flange Whiz Bolt, 3/8"-16 x 1" Thread Size, 3/4" Flange Diameter.
SIF 910 - Filter Box - 2 inch Merv 8 Filter	SIF 9-10 - Filter Box with 2 inch Merv 8 Filter
Show parts
	SIF910FB2INF [2 used]	2 Inch Filter Rack for Square Inline 9 & 10 Fan Filter Bank
	800032 [8 used]	A0005688 - Zinc-Plated Grade 5 Steel Serrated-Flange Locknut, 3/8"-16 Thread Size, 7/8" Large Flange Diameter, 11/32" Overall Height
	0120763.0800 [8 used]	A0031100 - 1"L, 1/4-20 Matpoint, Self Aligning, Hex Head, Grade 5 Bolt
	SIF910FBBP [2 used]	Back Post for Square Inline 9-10 Fan Filter Box
	SIF910FBB [1 used]	Base for Square Inline 9-10 Fan Filter Bank
	11626-03224 [8 used]	Cage Nut - 1/4" - 20. Installed in 1/2" square hole. Used on 20 gauge material.
	SIF910FBBRACKET [8 used]	Connecting Bracket for Square Inline 9-10 Fan Filter Bank
	SIF910FBFRBC [4 used]	Cover for the Filter Rack Blank for Square Inline 9-10 Fan Filter Bank
	SIF910FBD [2 used]	Door for Square Inline 9-10 Fan Filter Bank
	SIF910FBDL [2 used]	Door Liner for Square Inline 9-10 Fan Filter Bank
	SIF910FBFRB [2 used]	Filter Rack Back for Square Inline 9-10 Fan Filter Bank
	SIF910FBFR [2 used]	Filter Rack for Square Inline 9-10 Fan Filter Bank
	TA 16X16X2 [1 used]	Filter throw away 16" x 16" x 2". MERV 8. (DP40)
	SIF910FBFP [2 used]	Front Post for Square Inline 9-10 Fan Filter Box
	SB6-4-RIVET [94 used]	RIVET - 3/16" Diameter, .126 To .250 Grip Range, SB6-4 Button Head Steel/Steel. Replaced 800075.
	SIF910FBT [1 used]	Top for Square Inline 9-10 Fan Filter Bank
	11104711 [8 used]	Zinc-Plated Grade 5 Steel Serrated-Flange Whiz Bolt, 3/8"-16 x 1" Thread Size, 3/4" Flange Diameter.
SIF 910 - Filter Box - 2 inch Mesh Filter	SIF 9-10 - Filter Box with 2 inch Mesh Filter
Show parts
	SIF910FB2INF [2 used]	2 Inch Filter Rack for Square Inline 9 & 10 Fan Filter Bank
	800032 [8 used]	A0005688 - Zinc-Plated Grade 5 Steel Serrated-Flange Locknut, 3/8"-16 Thread Size, 7/8" Large Flange Diameter, 11/32" Overall Height
	0120763.0800 [8 used]	A0031100 - 1"L, 1/4-20 Matpoint, Self Aligning, Hex Head, Grade 5 Bolt
	SIF910FBBP [2 used]	Back Post for Square Inline 9-10 Fan Filter Box
	SIF910FBB [1 used]	Base for Square Inline 9-10 Fan Filter Bank
	11626-03224 [8 used]	Cage Nut - 1/4" - 20. Installed in 1/2" square hole. Used on 20 gauge material.
	SIF910FBBRACKET [8 used]	Connecting Bracket for Square Inline 9-10 Fan Filter Bank
	SIF910FBFRBC [4 used]	Cover for the Filter Rack Blank for Square Inline 9-10 Fan Filter Bank
	SIF910FBD [2 used]	Door for Square Inline 9-10 Fan Filter Bank
	SIF910FBDL [2 used]	Door Liner for Square Inline 9-10 Fan Filter Bank
	SIF910FBFRB [2 used]	Filter Rack Back for Square Inline 9-10 Fan Filter Bank
	SIF910FBFR [2 used]	Filter Rack for Square Inline 9-10 Fan Filter Bank
	SIF910FBFP [2 used]	Front Post for Square Inline 9-10 Fan Filter Box
	16X16 EZ Kleen [1 used]	MV EZ Kleen Metal Mesh Filter. 16"x 16"x 2" Used for heater and supply fan intakes.
	SB6-4-RIVET [94 used]	RIVET - 3/16" Diameter, .126 To .250 Grip Range, SB6-4 Button Head Steel/Steel. Replaced 800075.
	SIF910FBT [1 used]	Top for Square Inline 9-10 Fan Filter Bank
	11104711 [8 used]	Zinc-Plated Grade 5 Steel Serrated-Flange Whiz Bolt, 3/8"-16 x 1" Thread Size, 3/4" Flange Diameter.
SIF 910 - Filter Box - 4 inch HEPA Filter	SIF 9-10 - Filter Box with 4 inch HEPA Filter
Show parts
	800032 [8 used]	A0005688 - Zinc-Plated Grade 5 Steel Serrated-Flange Locknut, 3/8"-16 Thread Size, 7/8" Large Flange Diameter, 11/32" Overall Height
	0120763.0800 [8 used]	A0031100 - 1"L, 1/4-20 Matpoint, Self Aligning, Hex Head, Grade 5 Bolt
	SIF910FBBP [2 used]	Back Post for Square Inline 9-10 Fan Filter Box
	SIF910FBB [1 used]	Base for Square Inline 9-10 Fan Filter Bank
	11626-03224 [8 used]	Cage Nut - 1/4" - 20. Installed in 1/2" square hole. Used on 20 gauge material.
	SIF910FBBRACKET [8 used]	Connecting Bracket for Square Inline 9-10 Fan Filter Bank
	SIF910FBFRBC [4 used]	Cover for the Filter Rack Blank for Square Inline 9-10 Fan Filter Bank
	SIF910FBD [2 used]	Door for Square Inline 9-10 Fan Filter Bank
	SIF910FBDL [2 used]	Door Liner for Square Inline 9-10 Fan Filter Bank
	SIF910FBFRB [2 used]	Filter Rack Back for Square Inline 9-10 Fan Filter Bank
	SIF910FBFR [2 used]	Filter Rack for Square Inline 9-10 Fan Filter Bank
	SIF910FBFP [2 used]	Front Post for Square Inline 9-10 Fan Filter Box
	91801616 [1 used]	HEPA Filter. 16 x 16 x 4. Includes gasketing around the perimeter of filter and faceguard back screen.
	SB6-4-RIVET [94 used]	RIVET - 3/16" Diameter, .126 To .250 Grip Range, SB6-4 Button Head Steel/Steel. Replaced 800075.
	SIF910FBT [1 used]	Top for Square Inline 9-10 Fan Filter Bank
	11104711 [8 used]	Zinc-Plated Grade 5 Steel Serrated-Flange Whiz Bolt, 3/8"-16 x 1" Thread Size, 3/4" Flange Diameter.
SIF 910 - Filter Box - 4 inch Merv 15 Filter	SIF 9-10 - Filter Box with 4 inch Merv 15 Filter
Show parts
	800032 [8 used]	A0005688 - Zinc-Plated Grade 5 Steel Serrated-Flange Locknut, 3/8"-16 Thread Size, 7/8" Large Flange Diameter, 11/32" Overall Height
	0120763.0800 [8 used]	A0031100 - 1"L, 1/4-20 Matpoint, Self Aligning, Hex Head, Grade 5 Bolt
	SIF910FBBP [2 used]	Back Post for Square Inline 9-10 Fan Filter Box
	SIF910FBB [1 used]	Base for Square Inline 9-10 Fan Filter Bank
	11626-03224 [8 used]	Cage Nut - 1/4" - 20. Installed in 1/2" square hole. Used on 20 gauge material.
	SIF910FBBRACKET [8 used]	Connecting Bracket for Square Inline 9-10 Fan Filter Bank
	SIF910FBFRBC [4 used]	Cover for the Filter Rack Blank for Square Inline 9-10 Fan Filter Bank
	SIF910FBD [2 used]	Door for Square Inline 9-10 Fan Filter Bank
	SIF910FBDL [2 used]	Door Liner for Square Inline 9-10 Fan Filter Bank
	SIF910FBFRB [2 used]	Filter Rack Back for Square Inline 9-10 Fan Filter Bank
	SIF910FBFR [2 used]	Filter Rack for Square Inline 9-10 Fan Filter Bank
	SIF910FBFP [2 used]	Front Post for Square Inline 9-10 Fan Filter Box
	90801616 [1 used]	Merv 15 Filter. 16 x 16 x 4. Includes perimeter gasket on the downstream end and addition of face gasket on the downstream end.
	SB6-4-RIVET [94 used]	RIVET - 3/16" Diameter, .126 To .250 Grip Range, SB6-4 Button Head Steel/Steel. Replaced 800075.
	SIF910FBT [1 used]	Top for Square Inline 9-10 Fan Filter Bank
	11104711 [8 used]	Zinc-Plated Grade 5 Steel Serrated-Flange Whiz Bolt, 3/8"-16 x 1" Thread Size, 3/4" Flange Diameter.
SIF910SD-Inlet-Square	SIF9-10 - Square Duct Inlet Connection.
SIF910SD-Inlet-DW10FRISER	SIF910 Standard 10" Duct Inlet Connection.
Show parts
	800034 [8 used]	A0005690 - Nut Whiz 1/4-20, SFLN1420LZ, Steel, Large Flange
	0120763.0800 [8 used]	A0031100 - 1"L, 1/4-20 Matpoint, Self Aligning, Hex Head, Grade 5 Bolt
	SIF910DA [1 used]	Discharge Adapter used to go from SIF9-10 to round duct.
SIF910-InletAdapter-DW10FRISER	SIF910 Standard 10" Duct Inlet Connection for Filter Bank
Show parts
	SIF910DA [1 used]	Discharge Adapter used to go from SIF9-10 to round duct.
	SIF910SD-Inlet-DW10FRISER [1 used]	SIF910 Standard 10" Duct Inlet Connection.
SIF-Mount-Top(9-10)	SIF - Horizontal Overhead Pre-Installed Mounts (Used on sizes 9-10). Includes shipping brackets.
Show parts
	SIF910CRNRS [8 used]	Corner Support for wall/ ceiling mounting Square Inline Fan Sizes 9-10.
SIF-Mount-Loose(9-10)	SIF - Mounting Brackets Shipped Loose (Used on Sizes 9-10).
Show parts
	SIF910CRNRS [4 used]	Corner Support for wall/ ceiling mounting Square Inline Fan Sizes 9-10.
SIF-Mount-InletSide(9-10)	SIF -Vertical Floor Pre-Installed Mounts (Used on sizes 9-10). Includes shipping brackets.
Show parts
	SIF910CRNRS [6 used]	Corner Support for wall/ ceiling mounting Square Inline Fan Sizes 9-10.
SIF-Mount-DischargeSide(9-10)	SIF - Vertical Overhead Pre-Installed Mounts (Used on sizes 9-10). Includes shipping brackets.
Show parts
	SIF910CRNRS [4 used]	Corner Support for wall/ ceiling mounting Square Inline Fan Sizes 9-10.
5C126-4	Floor Mount Spring Vibration Isolators. Option for the BI10, USBI11, USBI13 & USBI15 (4 required) Utility Set units and SIF11-18 (4 required). Max Weight = 75 lbs. 1.3" Deflection. 3/8" bolt diameter. Set of 4. "Orange" (5C126x4) Grainger equivalent = 5C126 - Mason C-A-75.
Show parts
	5C126 [4 used]	Floor Mount Spring Vibration Isolators. Option for the BI10 and BI11 (4 required) thru BI18 (6 required) Utility Set and MUA units. Max Weight = 75 lbs. 1.3" Deflection. 3/8" bolt diameter. (Sold separately for inddor/outside use). "Orange" (5C126) - Mason C-A-75.
8860041-4	Rubber Vibration Floor Isolators for In-Line Exhaust Fans (set of 4). Option for the SQB10 thru SQB15. (5079)
Show parts
	T44-5A [4 used]	Vibration Isolators for Utility Set Exhaust Fans and PCU blowers. Option for the BI-RM Utility Set. (Sold separately.) (5079) (T44-5A)

Security Policy		Privacy Policy		Legal Notice		Warranty		Return Policy
Copyright ® 2003-2014 Thermotek All Rights Reserved.