Fan Parts

Home About Us Contact Us Help

Buy Online or Call 1-800-476-5888

Heaters

Exhaust Fans

Make-Up Air

Accessories » Economy Inline Filtered Modular Packaged Unit Rooftop Filtered

Cooling Modules Heating Modules Intake/Discharge Accessories

DUCTWORK

Single Wall Grease Duct Double Wall Grease Duct Chimney Special Gas Vent HVAC Supply Duct

Kitchen Ventilation

HVAC

CASLINK

Resources

TTH 30 with 36" burner Parts

Motors, Pulleys, & Motor Specific Parts

Motor HP Phs Voltage FLA Shaft Frame Weight RPM Vendor

DTP7/54 7.500 3 200-208-230/380/400/460 V 21.5-21.1-19.1/11.4/10.8/9.6 1.375" 213T 104 lbs 1750 Mimco/TECO

ODP, Premium (E-Plus3) Eff. Pulleys

Show parts


100-C23D400	208 V	Contactor - 120V, 50/60Hz Coil, Rated for 23 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

100-C23D400	230 V	Contactor - 120V, 50/60Hz Coil, Rated for 23 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

100-C23D400	460 V	Contactor - 120V, 50/60Hz Coil, Rated for 23 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

100-C23D400	200 V	Contactor - 120V, 50/60Hz Coil, Rated for 23 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

100-C23D400	400 V	Contactor - 120V, 50/60Hz Coil, Rated for 23 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

100-C23D400	380 V	Contactor - 120V, 50/60Hz Coil, Rated for 23 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

01018OT3H215T-S 10.000 3 575 V 9.9 1.375" 215T 137 lbs 1750 WEG

ODP, Premium (E-Plus3) Eff. Pulleys

Show parts


100-C23D400	575 V	Contactor - 120V, 50/60Hz Coil, Rated for 23 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

DTP0104 10.000 3 190/208-230/380/460 V 29.9/27-24.4/15/12.2 1.375" 215T 143 lbs 1755 Mimco/TECO

ODP, Premium (E-Plus3) Eff. Pulleys

Show parts


100-C40D400	208 V	Contactor - 120V, 50/60Hz Coil, Rated for 40 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

100-C40D400	230 V	Contactor - 120V, 50/60Hz Coil, Rated for 40 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

100-C23D400	460 V	Contactor - 120V, 50/60Hz Coil, Rated for 23 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

100-C40D400	190 V	Contactor - 120V, 50/60Hz Coil, Rated for 40 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

100-C23D400	380 V	Contactor - 120V, 50/60Hz Coil, Rated for 23 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

DTP0154 15.000 3 208-230/380/460 V 40.3-36.4/22.7/18.2 1.625" 254T 231 lbs 1755 Mimco/TECO

ODP, Premium (E-Plus3) Eff. Pulleys

Show parts


100-C97D10	208 V	Contactor - 120V, 50/60Hz Coil, Rated for 97 AMPs.

100-C40D400	230 V	Contactor - 120V, 50/60Hz Coil, Rated for 40 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

100-C23D400	460 V	Contactor - 120V, 50/60Hz Coil, Rated for 23 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

100-C23D400	380 V	Contactor - 120V, 50/60Hz Coil, Rated for 23 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

01518OT3H254T-S 15.000 3 575 V 14.9 1.625" 254T 175 lbs 1750 WEG

ODP, Premium (E-Plus3) Eff. Pulleys

Show parts


100-C23D400	575 V	Contactor - 120V, 50/60Hz Coil, Rated for 23 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

02018OT3H256T-S 20.000 3 575 V 20 1.625" 256T 198 lbs 1750 WEG

ODP, Premium (E-Plus3) Eff. Pulleys

Show parts


100-C23D400	575 V	Contactor - 120V, 50/60Hz Coil, Rated for 23 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

DTP0204 20.000 3 208-230/460 V 53.7-48.6/24.3 1.625" 256T 269 lbs 1770 Mimco/TECO

ODP, Premium (E-Plus3) Eff. Pulleys

Show parts


100-C97D10	208 V	Contactor - 120V, 50/60Hz Coil, Rated for 97 AMPs.

100-C97D10	230 V	Contactor - 120V, 50/60Hz Coil, Rated for 97 AMPs.

100-C40D400	460 V	Contactor - 120V, 50/60Hz Coil, Rated for 40 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

DTP0254-50 25.000 3 190/380 V 70.2/35.1 1.875" 284T 710 lbs 1453 Mimco/TECO

ODP, Premium (E-Plus3) Eff. Pulleys

Show parts


100-C97D10	190 V	Contactor - 120V, 50/60Hz Coil, Rated for 97 AMPs.

100-C40D400	380 V	Contactor - 120V, 50/60Hz Coil, Rated for 40 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

DTP0254 25.000 3 208-230/460 V 65-58.8/29.4 1.875" 284T 339 lbs 1765 Mimco/TECO

ODP, Premium (E-Plus3) Eff. Pulleys

Show parts


100-C97D10	208 V	Contactor - 120V, 50/60Hz Coil, Rated for 97 AMPs.

100-C97D10	230 V	Contactor - 120V, 50/60Hz Coil, Rated for 97 AMPs.

100-C40D400	460 V	Contactor - 120V, 50/60Hz Coil, Rated for 40 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

02518OT3H284T-W40 25.000 3 575 V 23.6 1.875" 284 350 lbs 1770 WEG

ODP, Premium (E-Plus3) Eff. Pulleys

Show parts


100-C40D400	575 V	Contactor - 120V, 50/60Hz Coil, Rated for 40 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

03018OT3H286T-W40 30.000 3 575 V 27.9 1.625" 286T 396 lbs 1770 WEG

ODP, Premium (E-Plus3) Eff. Pulleys

Show parts


100-C40D400	575 V	Contactor - 120V, 50/60Hz Coil, Rated for 40 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

DTP0304 30.000 3 208-230/460 V 76.7-69.4/34.7 1.875" 286T 283 lbs 1770 Mimco/TECO

ODP, Premium (E-Plus3) Eff. Pulleys

Show parts


100-C97D10	208 V	Contactor - 120V, 50/60Hz Coil, Rated for 97 AMPs.

100-C97D10	230 V	Contactor - 120V, 50/60Hz Coil, Rated for 97 AMPs.

100-C40D400	460 V	Contactor - 120V, 50/60Hz Coil, Rated for 40 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

DHP0404 40.000 3 208-230/460 V 102.4-92.6/46.3 2.125" 324T 338 lbs 1770 Mimco/TECO

ODP, Premium (E-Plus3) Eff. Pulleys

Show parts


100-C97D10	230 V	Contactor - 120V, 50/60Hz Coil, Rated for 97 AMPs.

100-C97D10	460 V	Contactor - 120V, 50/60Hz Coil, Rated for 97 AMPs.

100-E116KD11	208 V	Contactor - 120V, 50/60Hz Coil, Rated for 115 AMPs. Used only with Rockwell 193-EEHF System Overloads. (old p/n:100-D115D11 discontinued and replaced w/ 100-E116KD11)

00718ET3H213T-W22 7.500 3 575 V 7.3 1.375" 213T 174 lbs 1750 WEG

TEFC, Premium (E-Plus3) Eff. Pulleys

Show parts


100-C23D400	575 V	Contactor - 120V, 50/60Hz Coil, Rated for 23 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

01018ET3H215T-W22 10.000 3 575 V 9.9 1.375" 215T 188 lbs 1750 WEG

TEFC, Premium (E-Plus3) Eff. Pulleys

Show parts


100-C23D400	575 V	Contactor - 120V, 50/60Hz Coil, Rated for 23 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

01518ET3H254T-W22 15.000 3 575 V 14.4 1.625" 254T 347 lbs 1750 WEG

TEFC, Premium (E-Plus3) Eff. Pulleys

Show parts


100-C23D400	575 V	Contactor - 120V, 50/60Hz Coil, Rated for 23 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

NP0154 15.000 3 190/208-230/380/460 V 41.8/38.2-34.5/20.9/17.3 1.625" 254T 250 lbs 1765 Mimco/TECO

TEFC, Premium (E-Plus3) Eff. Pulleys

Show parts


100-C40D400	208 V	Contactor - 120V, 50/60Hz Coil, Rated for 40 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

100-C40D400	230 V	Contactor - 120V, 50/60Hz Coil, Rated for 40 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

100-C23D400	460 V	Contactor - 120V, 50/60Hz Coil, Rated for 23 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

100-C97D10	190 V	Contactor - 120V, 50/60Hz Coil, Rated for 97 AMPs.

100-C23D400	380 V	Contactor - 120V, 50/60Hz Coil, Rated for 23 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

NP0204 20.000 3 190/208-230/380/460 V 55.7/50.8-46/27.8/23 1.625" 256T 287 lbs 1760 Mimco/TECO

TEFC, Premium (E-Plus3) Eff. Pulleys

Show parts


100-C97D10	208 V	Contactor - 120V, 50/60Hz Coil, Rated for 97 AMPs.

100-C97D10	230 V	Contactor - 120V, 50/60Hz Coil, Rated for 97 AMPs.

100-C23D400	460 V	Contactor - 120V, 50/60Hz Coil, Rated for 23 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

100-C97D10	190 V	Contactor - 120V, 50/60Hz Coil, Rated for 97 AMPs.

100-C40D400	380 V	Contactor - 120V, 50/60Hz Coil, Rated for 40 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

02018ET3H256T-W22 20.000 3 575 V 19.3 1.625" 256T 396 lbs 1750 WEG

TEFC, Premium (E-Plus3) Eff. Pulleys

Show parts


100-C23D400	575 V	Contactor - 120V, 50/60Hz Coil, Rated for 23 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

NP0254 25.000 3 208-230/460 V 64.3-58.2/29.1 1.875" 284T 358 lbs 1765 Mimco/TECO

TEFC, Premium (E-Plus3) Eff. Pulleys

Show parts


100-C97D10	208 V	Contactor - 120V, 50/60Hz Coil, Rated for 97 AMPs.

100-C97D10	230 V	Contactor - 120V, 50/60Hz Coil, Rated for 97 AMPs.

100-C40D400	460 V	Contactor - 120V, 50/60Hz Coil, Rated for 40 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

02518ET3H284T-W22 25.000 3 575 V 23.6 1.875" 284T 412 lbs 1750 WEG

TEFC, Premium (E-Plus3) Eff. Pulleys

Show parts


100-C40D400	575 V	Contactor - 120V, 50/60Hz Coil, Rated for 40 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

NP0304 30.000 3 208-230/460 V 75.8-68.6/34.3 1.875" 286T 436 lbs 1765 Mimco/TECO

TEFC, Premium (E-Plus3) Eff. Pulleys

Show parts


100-C97D10	208 V	Contactor - 120V, 50/60Hz Coil, Rated for 97 AMPs.

100-C40D400	460 V	Contactor - 120V, 50/60Hz Coil, Rated for 40 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

100-C97D10	230 V	Contactor - 120V, 50/60Hz Coil, Rated for 97 AMPs.

03018ET3H286T-W22 30.000 3 575 V 28.1 1.875" 286T 450 lbs 1750 WEG

TEFC, Premium (E-Plus3) Eff. Pulleys

Show parts


100-C40D400	575 V	Contactor - 120V, 50/60Hz Coil, Rated for 40 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

04018ET3H324T-W22 40.000 3 575 V 37.7 2.125" 324T 574 lbs 1750 WEG

TEFC, Premium (E-Plus3) Eff. Pulleys

Show parts


100-C40D400	575 V	Contactor - 120V, 50/60Hz Coil, Rated for 40 AMPs. 4-pole (aux contact not present). Used only with Rockwell 193-T1A System Overloads. Used when switching 2 single phase motors.

NP0404 40.000 3 208-230/460 V 102.3-92.6/46.3 2.125" 324T 661 lbs 1770 Mimco/TECO

TEFC, Premium (E-Plus3) Eff. Pulleys

Show parts


100-E116KD11	208 V	Contactor - 120V, 50/60Hz Coil, Rated for 115 AMPs. Used only with Rockwell 193-EEHF System Overloads. (old p/n:100-D115D11 discontinued and replaced w/ 100-E116KD11)

100-C97D10	230 V	Contactor - 120V, 50/60Hz Coil, Rated for 97 AMPs.

100-C97D10	460 V	Contactor - 120V, 50/60Hz Coil, Rated for 97 AMPs.

The manufacturer reserves the right to use alternate motors from alternate vendors that meet the operating requirements of the fan but may have slightly different specifications.

Intakes & Intake Parts

Part

IH4-O-FDH Full downturn intake hood. 80.25" wide, 58" deep, 52.75 high.

IH4-O-IHNF Intake Hood - 80.25" Width X 95.25" Length X 52.75" Height

Show parts

M1053H1M

[ 2 Used ]

Lifting Eye Support Accessory 2.31 x 17 x 12 ga.

M4212H1H

[ 1 Used ]

RAM 4 Intake Hood Hat Channel 7.71 x 80.44 x 18 ga.

SB6-4-RIVET

[ 30 Used ]

RIVET - 3/16" Diameter, .126 To .250 Grip Range, SB6-4 Button Head Steel/Steel. Replaced 800075.

ITH41234

[ 127 Used ]

SHEET METAL SCREWS 12-14 X 3/4"

M4211H1H

[ 3 Used ]

Size 4 Industrial Horizontal Intake Hood Middle Filter rail (Right) 3.79 x 101.05

M4210H1H

[ 3 Used ]

Size 4 Industrial Horizontal Intake Hood Middle Rail (Left) 3.79 x 101.05 x 18 ga.

IH4-O-IH2"EZ Intake Hood Outdoor - 80.25" Width X 95.25" Length X 52.75" Height With 2" EZ Filter Max CFM = 34500

Show parts

M1053H1M

[ 2 Used ]

Lifting Eye Support Accessory 2.31 x 17 x 12 ga.

9151

[ 16 Used ]

MV EZ Kleen Metal Mesh Filter. 20"x 25"x 2" Used for heater and supply fan intakes. (3416)

M4212H1H

[ 1 Used ]

RAM 4 Intake Hood Hat Channel 7.71 x 80.44 x 18 ga.

SB6-4-RIVET

[ 30 Used ]

RIVET - 3/16" Diameter, .126 To .250 Grip Range, SB6-4 Button Head Steel/Steel. Replaced 800075.

ITH41234

[ 127 Used ]

SHEET METAL SCREWS 12-14 X 3/4"

M4211H1H

[ 3 Used ]

Size 4 Industrial Horizontal Intake Hood Middle Filter rail (Right) 3.79 x 101.05

M4210H1H

[ 3 Used ]

Size 4 Industrial Horizontal Intake Hood Middle Rail (Left) 3.79 x 101.05 x 18 ga.

IH4-O-VB2"TA-IH2"EZ V-BANK - 80.25" Width X 123.25" Length X 52.75" Height 2" TA Filters, Standard 2" EZ Filter With Intake Hood MERV 8 Filters

Show parts

83600.005

[ 1 Used ]

Door gasket used on industrial units, 3/16" thickness, 3/4" wide, sold by the roll (25').

TA 20X25X2

[ 20 Used ]

Filter throw away filter 20" x 25" x 2". MERV 8. (DP40), 12 per box

M1053H1M

[ 4 Used ]

Lifting Eye Support Accessory 2.31 x 17 x 12 ga.

9151

[ 16 Used ]

MV EZ Kleen Metal Mesh Filter. 20"x 25"x 2" Used for heater and supply fan intakes. (3416)

M4212H1H

[ 2 Used ]

RAM 4 Intake Hood Hat Channel 7.71 x 80.44 x 18 ga.

SB6-4-RIVET

[ 50 Used ]

RIVET - 3/16" Diameter, .126 To .250 Grip Range, SB6-4 Button Head Steel/Steel. Replaced 800075.

ITH41234

[ 249 Used ]

SHEET METAL SCREWS 12-14 X 3/4"

M4211H1H

[ 3 Used ]

Size 4 Industrial Horizontal Intake Hood Middle Filter rail (Right) 3.79 x 101.05

M4210H1H

[ 3 Used ]

Size 4 Industrial Horizontal Intake Hood Middle Rail (Left) 3.79 x 101.05 x 18 ga.

M4217H1F

[ 1 Used ]

Size 4/8 Industrial Horizontal 27/30, 227/230 Filter Section Door 26.00 x 54.06 x 20 ga.

IH4-O-VB2"EZ-IH2"EZ V-BANK - 80.25" Width X 123.25" Length X 52.75" Height, Standard 2" EZ Filter With Intake Hood

Show parts

83600.005

[ 1 Used ]

Door gasket used on industrial units, 3/16" thickness, 3/4" wide, sold by the roll (25').

M1053H1M

[ 2 Used ]

Lifting Eye Support Accessory 2.31 x 17 x 12 ga.

M1053H1M

[ 2 Used ]

Lifting Eye Support Accessory 2.31 x 17 x 12 ga.

9151

[ 16 Used ]

MV EZ Kleen Metal Mesh Filter. 20"x 25"x 2" Used for heater and supply fan intakes. (3416)

9151

[ 20 Used ]

MV EZ Kleen Metal Mesh Filter. 20"x 25"x 2" Used for heater and supply fan intakes. (3416)

M4212H1H

[ 1 Used ]

RAM 4 Intake Hood Hat Channel 7.71 x 80.44 x 18 ga.

M4212H1H

[ 1 Used ]

RAM 4 Intake Hood Hat Channel 7.71 x 80.44 x 18 ga.

SB6-4-RIVET

[ 30 Used ]

RIVET - 3/16" Diameter, .126 To .250 Grip Range, SB6-4 Button Head Steel/Steel. Replaced 800075.

SB6-4-RIVET

[ 20 Used ]

RIVET - 3/16" Diameter, .126 To .250 Grip Range, SB6-4 Button Head Steel/Steel. Replaced 800075.

ITH41234

[ 122 Used ]

SHEET METAL SCREWS 12-14 X 3/4"

ITH41234

[ 127 Used ]

SHEET METAL SCREWS 12-14 X 3/4"

M4211H1H

[ 3 Used ]

Size 4 Industrial Horizontal Intake Hood Middle Filter rail (Right) 3.79 x 101.05

M4210H1H

[ 3 Used ]

Size 4 Industrial Horizontal Intake Hood Middle Rail (Left) 3.79 x 101.05 x 18 ga.

M4217H1F

[ 1 Used ]

Size 4/8 Industrial Horizontal 27/30, 227/230 Filter Section Door 26.00 x 54.06 x 20 ga.

IH4-O-VB2"TA-FDH V-BANK - 80.25" Width X 86" Length X 52.75" Height, Standard 2" TA Filter With Full Downturn Hood MERV 8 Filters

Show parts

83600.005

[ 1 Used ]

Door gasket used on industrial units, 3/16" thickness, 3/4" wide, sold by the roll (25').

TA 20X25X2

[ 20 Used ]

Filter throw away filter 20" x 25" x 2". MERV 8. (DP40), 12 per box

IH4-O-VB2"EZ-IHNF V-BANK - 80.25" Width X 122.25" Length X 52.75" Height With Standard 2" EZ Filter And Intake Hood w/ No Filters

Show parts

83600.005

[ 1 Used ]

Door gasket used on industrial units, 3/16" thickness, 3/4" wide, sold by the roll (25').

M1053H1M

[ 4 Used ]

Lifting Eye Support Accessory 2.31 x 17 x 12 ga.

9151

[ 20 Used ]

MV EZ Kleen Metal Mesh Filter. 20"x 25"x 2" Used for heater and supply fan intakes. (3416)

M4212H1H

[ 2 Used ]

RAM 4 Intake Hood Hat Channel 7.71 x 80.44 x 18 ga.

SB6-4-RIVET

[ 50 Used ]

RIVET - 3/16" Diameter, .126 To .250 Grip Range, SB6-4 Button Head Steel/Steel. Replaced 800075.

ITH41234

[ 249 Used ]

SHEET METAL SCREWS 12-14 X 3/4"

M4211H1H

[ 3 Used ]

Size 4 Industrial Horizontal Intake Hood Middle Filter rail (Right) 3.79 x 101.05

M4210H1H

[ 3 Used ]

Size 4 Industrial Horizontal Intake Hood Middle Rail (Left) 3.79 x 101.05 x 18 ga.

M4217H1F

[ 1 Used ]

Size 4/8 Industrial Horizontal 27/30, 227/230 Filter Section Door 26.00 x 54.06 x 20 ga.

IH4-O-VB2"TA13-IHNF V-BANK - 80.25" Width X 122.25" Length X 52.75" Height With Standard 2" Pleated Filter w/Intake Hood w/No Filters MERV 13 Filters

Show parts

83600.005

[ 1 Used ]

Door gasket used on industrial units, 3/16" thickness, 3/4" wide, sold by the roll (25').

M1053H1M

[ 4 Used ]

Lifting Eye Support Accessory 2.31 x 17 x 12 ga.

M4212H1H

[ 2 Used ]

RAM 4 Intake Hood Hat Channel 7.71 x 80.44 x 18 ga.

SB6-4-RIVET

[ 50 Used ]

RIVET - 3/16" Diameter, .126 To .250 Grip Range, SB6-4 Button Head Steel/Steel. Replaced 800075.

ITH41234

[ 249 Used ]

SHEET METAL SCREWS 12-14 X 3/4"

M4211H1H

[ 3 Used ]

Size 4 Industrial Horizontal Intake Hood Middle Filter rail (Right) 3.79 x 101.05

M4210H1H

[ 3 Used ]

Size 4 Industrial Horizontal Intake Hood Middle Rail (Left) 3.79 x 101.05 x 18 ga.

M4217H1F

[ 1 Used ]

Size 4/8 Industrial Horizontal 27/30, 227/230 Filter Section Door 26.00 x 54.06 x 20 ga.

DP13-STD2-204

[ 20 Used ]

Throw away filter 20w x 25h x 2d, MERV13 rating, 1750 max cfm. 12 per box

IH4-O-VB2"TA13-VB2"TA-IHNF V-BANK - 80.25" Width X 122.25" Length X 52.75" Height With Standard 2" Pleated Filter w/Intake Hood w/No Filters MERV 13 Filters

Show parts

83600.005

[ 1 Used ]

Door gasket used on industrial units, 3/16" thickness, 3/4" wide, sold by the roll (25').

83600.005

[ 1 Used ]

Door gasket used on industrial units, 3/16" thickness, 3/4" wide, sold by the roll (25').

TA 20X25X2

[ 20 Used ]

Filter throw away filter 20" x 25" x 2". MERV 8. (DP40), 12 per box

M1053H1M

[ 2 Used ]

Lifting Eye Support Accessory 2.31 x 17 x 12 ga.

M1053H1M

[ 4 Used ]

Lifting Eye Support Accessory 2.31 x 17 x 12 ga.

M4212H1H

[ 2 Used ]

RAM 4 Intake Hood Hat Channel 7.71 x 80.44 x 18 ga.

M4212H1H

[ 1 Used ]

RAM 4 Intake Hood Hat Channel 7.71 x 80.44 x 18 ga.

SB6-4-RIVET

[ 20 Used ]

RIVET - 3/16" Diameter, .126 To .250 Grip Range, SB6-4 Button Head Steel/Steel. Replaced 800075.

SB6-4-RIVET

[ 50 Used ]

RIVET - 3/16" Diameter, .126 To .250 Grip Range, SB6-4 Button Head Steel/Steel. Replaced 800075.

ITH41234

[ 249 Used ]

SHEET METAL SCREWS 12-14 X 3/4"

ITH41234

[ 122 Used ]

SHEET METAL SCREWS 12-14 X 3/4"

M4211H1H

[ 3 Used ]

Size 4 Industrial Horizontal Intake Hood Middle Filter rail (Right) 3.79 x 101.05

M4210H1H

[ 3 Used ]

Size 4 Industrial Horizontal Intake Hood Middle Rail (Left) 3.79 x 101.05 x 18 ga.

M4217H1F

[ 1 Used ]

Size 4/8 Industrial Horizontal 27/30, 227/230 Filter Section Door 26.00 x 54.06 x 20 ga.

M4217H1F

[ 1 Used ]

Size 4/8 Industrial Horizontal 27/30, 227/230 Filter Section Door 26.00 x 54.06 x 20 ga.

DP13-STD2-204

[ 20 Used ]

Throw away filter 20w x 25h x 2d, MERV13 rating, 1750 max cfm. 12 per box

IH4-O-VB2"TA-IHNF V-BANK - 80.25" Width X 122.25" Length X 52.75" Height With Standard 2" Pleated Filter w/Intake Hood w/No Filters MERV 8 Filters

Show parts

83600.005

[ 1 Used ]

Door gasket used on industrial units, 3/16" thickness, 3/4" wide, sold by the roll (25').

TA 20X25X2

[ 20 Used ]

Filter throw away filter 20" x 25" x 2". MERV 8. (DP40), 12 per box

M1053H1M

[ 4 Used ]

Lifting Eye Support Accessory 2.31 x 17 x 12 ga.

M4212H1H

[ 2 Used ]

RAM 4 Intake Hood Hat Channel 7.71 x 80.44 x 18 ga.

SB6-4-RIVET

[ 50 Used ]

RIVET - 3/16" Diameter, .126 To .250 Grip Range, SB6-4 Button Head Steel/Steel. Replaced 800075.

ITH41234

[ 249 Used ]

SHEET METAL SCREWS 12-14 X 3/4"

M4211H1H

[ 3 Used ]

Size 4 Industrial Horizontal Intake Hood Middle Filter rail (Right) 3.79 x 101.05

M4210H1H

[ 3 Used ]

Size 4 Industrial Horizontal Intake Hood Middle Rail (Left) 3.79 x 101.05 x 18 ga.

M4217H1F

[ 1 Used ]

Size 4/8 Industrial Horizontal 27/30, 227/230 Filter Section Door 26.00 x 54.06 x 20 ga.

IH4-O-VB2"TA13-IH2"EZ V-BANK - 80.25" Width X 123.25" Length X 52.75" Height 2" TA Filters, Standard 2" EZ Filter With Intake Hood MERV 13 Filters

Show parts

83600.005

[ 1 Used ]

Door gasket used on industrial units, 3/16" thickness, 3/4" wide, sold by the roll (25').

9151

[ 16 Used ]

MV EZ Kleen Metal Mesh Filter. 20"x 25"x 2" Used for heater and supply fan intakes. (3416)

DP13-STD2-204

[ 20 Used ]

Throw away filter 20w x 25h x 2d, MERV13 rating, 1750 max cfm. 12 per box

IH4-I-VB2"TA V-BANK - 80.25" Width X 28" Length X 52.75" Height for Horizontal Industrial With Standard 2" Pleated Filter MERV 8 Filters

Show parts

83600.005

[ 1 Used ]

Door gasket used on industrial units, 3/16" thickness, 3/4" wide, sold by the roll (25').

TA 20X25X2

[ 20 Used ]

Filter throw away filter 20" x 25" x 2". MERV 8. (DP40), 12 per box

M1053H1M

[ 2 Used ]

Lifting Eye Support Accessory 2.31 x 17 x 12 ga.

M4212H1H

[ 1 Used ]

RAM 4 Intake Hood Hat Channel 7.71 x 80.44 x 18 ga.

SB6-4-RIVET

[ 20 Used ]

RIVET - 3/16" Diameter, .126 To .250 Grip Range, SB6-4 Button Head Steel/Steel. Replaced 800075.

ITH41234

[ 122 Used ]

SHEET METAL SCREWS 12-14 X 3/4"

M4217H1F

[ 1 Used ]

Size 4/8 Industrial Horizontal 27/30, 227/230 Filter Section Door 26.00 x 54.06 x 20 ga.

IH4-I-VB2"TA13 V-BANK - 80.25" Width X 28" Length X 52.75" Height for Horizontal Industrial With Standard 2" Pleated Filter MERV 13 Filters

Show parts

M1053H1M

[ 2 Used ]

Lifting Eye Support Accessory 2.31 x 17 x 12 ga.

M4212H1H

[ 1 Used ]

RAM 4 Intake Hood Hat Channel 7.71 x 80.44 x 18 ga.

SB6-4-RIVET

[ 20 Used ]

RIVET - 3/16" Diameter, .126 To .250 Grip Range, SB6-4 Button Head Steel/Steel. Replaced 800075.

ITH41234

[ 122 Used ]

SHEET METAL SCREWS 12-14 X 3/4"

M4217H1F

[ 1 Used ]

Size 4/8 Industrial Horizontal 27/30, 227/230 Filter Section Door 26.00 x 54.06 x 20 ga.

DP13-STD2-204

[ 20 Used ]

Throw away filter 20w x 25h x 2d, MERV13 rating, 1750 max cfm. 12 per box

IH4-I-VB2"EZ V-BANK - 80.25" Width X 28" Length X 52.75" Height for Industrial Horizontal With Standard 2" EZ Filter

Show parts

83600.005

[ 1 Used ]

Door gasket used on industrial units, 3/16" thickness, 3/4" wide, sold by the roll (25').

M1053H1M

[ 2 Used ]

Lifting Eye Support Accessory 2.31 x 17 x 12 ga.

9151

[ 20 Used ]

MV EZ Kleen Metal Mesh Filter. 20"x 25"x 2" Used for heater and supply fan intakes. (3416)

M4212H1H

[ 1 Used ]

RAM 4 Intake Hood Hat Channel 7.71 x 80.44 x 18 ga.

SB6-4-RIVET

[ 20 Used ]

RIVET - 3/16" Diameter, .126 To .250 Grip Range, SB6-4 Button Head Steel/Steel. Replaced 800075.

ITH41234

[ 122 Used ]

SHEET METAL SCREWS 12-14 X 3/4"

M4217H1F

[ 1 Used ]

Size 4/8 Industrial Horizontal 27/30, 227/230 Filter Section Door 26.00 x 54.06 x 20 ga.

IH4-O-VB2"TA13-FDH V-BANK - 80.25" Width X 86" Length X 52.75" Height, Standard 2" TA Filter With Full Downturn Hood MERV 13 Filters

Show parts

83600.005

[ 1 Used ]

Door gasket used on industrial units, 3/16" thickness, 3/4" wide, sold by the roll (25').

DP13-STD2-204

[ 20 Used ]

Throw away filter 20w x 25h x 2d, MERV13 rating, 1750 max cfm. 12 per box

Temperature Controls

No Temperature Controls Found.

Gas Manifold Parts

No Gas Manifold Parts Found.

Blower

Part
A30-30H	BLOWER 30" - Enamel finish, pillow block bearing, 0-51000 CFM, 50 HP, 2 7/16 x 65" Shaft, 650 MAX RPM, used in heated and non-heated supply fans

Burner

Part

36-P-(3)12-EI Direct-fired burner assembly. 1,710,000 BTU/HR Maximum, 57,000 minimum. 36" long. Used in size 2 industrial vertical and horizontal direct-fired heaters. Used for both Natural and Propane Gas. Pilot/Flame Rod/Spark Assembly included.

1190850
[1 used]

BURNER PART - "BRUTE" PILOT ASSEMBLY W/ SPARK & FLAME ROD. Pilot hole size is drill #50 (.070 diameter) (342B) (A0003270) Includes pack of boots and hardware. REPLACES 1190870

1352-52
[1 used]

BURNER PART - 1 1/2" INLET FLANGE - ALUMINUM

1010810
[3 used]

BURNER PART - 12" STRAIGHT SECTION - HMA-2A (Aluminum)

1372-52
[1 used]

BURNER PART - BLANK END FLANGE - ALUMINUM

1354-50
[1 used]

BURNER PART - SS End Plate

1354-60
[1 used]

BURNER PART - SS End Plate W/ PILOT MOUNT

Replacement Parts

Part
PN10-10RX-L [1 used]	Yellow Ring Expanded Entry for GTO Cable - Panduit Used on ignition transformers
HMI_Bracket [1 used]	20 GA. Galvanized. Used on IBT controls
Controller&HMI
HMI_01_MUA_POPULATED [1 used]	HMI assembly. Preprogrammed for use with MUA Board. Includes CASHMI PCB, 4 mounting screws, 16 ga. SS backing plate, membrane switches & gasket. HMI should have populated RH sensor.
Direct Fired Air Movement Control Components
17045A [4 used]	Airflow Switch Components Cleveland Controls Airflow Probe 4".
Direct Fired Components
85000.002 [4 used]	Standard Lifiting Eye for Industrial Horizontal Heaters Size 2-8, 3/8" plate.
Direct Fired Flame Control Components
M4RT1 [1 used]	Fireye Flame Safety Control. Direct replacement for M series 2. Pre-purge preset 5 Sec. PTFI preset 10 Sec. Recycles once only after flame signal loss. Wiring connections are identical to M series 2.
Direct Fired Sheet Metal Components
M4BLDRAS [1 used]	Assembled blower acccess door for size 4 & 8 horizontal industrial unit. Includes hinge, latches, liner and insulation.
M4VDRAS [1 used]	Assembled vestibule acccess door for size 4 and 8 horizontal industrial unit. Includes hinge, liner and insulation.
M4VDRASLA [1 used]	Assembled vestibule acccess door for size 4 horizontal industrial unit. Includes hinge, latches, liner and insulation.
M4075H1W [1 used]	Back wall heat shield used in size 4 and size 8 industrial horizontal industrial units
M4042H1B [1 used]	Base frame middle used on size 4 industrial horizontal units
M400304B [1 used]	Base frame motor used on size 4 industrial horizontal units
M400259B [1 used]	Base frame side used on size 4 and 8 industrial horizontal units
M400258B [1 used]	Base side used on size 4 and 8 industrial horizontal units
M4041H1B [2 used]	Base side used on size 4 industrial horizontal units
M4114H1I [1 used]	Burner base used on size 4 industrial horizontal units
M300039W [1 used]	Door jam, upper RH used on size 3 and size 7 industrial horizontal units
M3002H1B [1 used]	Floor panel back side used on size 4 industrial horizontal units with 30" blower
M400248B [1 used]	Floor panel back used on size 4 industrial horizontal units
M4008H1B [1 used]	Floor panel motor side used on size 4 industrial horizontal units with 30" blower
M4097H1I [1 used]	Floor support used on size 4 industrial horizontal units
M3038H1W [1 used]	Lower door jamb blower access door used on size 3 horizontal industrial unit.
M1017H1W [1 used]	PILOT ACCESS PANEL FOR INDUSTRIAL DIRECT FIRED HEATERS
M400565W [1 used]	REAR WALL PANEL, 62H X 22.7W
M1101H1W [1 used]	Sheet Metal Cover Plate for Industrial Flame Observation Port, used with ASTM-V-7.
M4100H1I [1 used]	Vestibule back used on size 4 and 8 industrial horizontal units
M4104H1I [1 used]	Vestibule heat shield used on size 4 and 8 industrial horizontal units
M4110H1I [1 used]	Vestibule intake side used on size 4 and 8 industrial horizontal units
M4060H1W [1 used]	VESTIBULE LOWER DOOR JAMB SIZE 4 AND SIZE 8 INDUSTRIAL HORIZONTAL UNITS.
M4255H1I [1 used]	Vestibule roof liner used on size 4 and 8 industrial horizontal units
M4113H1I [1 used]	Vestibule shelf used on size 4 and 8 industrial horizontal units
M4109H1I [1 used]	Vestibule side used on size 4 and 8 industrial horizontal units
M4046H1W [1 used]	WALL PANEL, 18GA G90, 30.25W X 62H
Miscellaneous Electrical Parts
CAT5_3FT [1 used]	3 Foot Long CAT5 Cable
MUA Board [1 used]	Printed Circuit board for use in heaters. Used in conjunction with CAS HMI.
Miscellaneous Heater Components
62-99-805-20 [2 used]	Door latch used on industrial units, can be locked unlocked with tool
62-99-804-20 (P90-9910) [2 used]	Door latch used on make up air units and pollution control units, no tool needed for access. Includes gasket. A0006143
206525 [1 used]	Yellow Label Sheet Package for Industrial MAUs.
Product Manuals
MANUAL INDUST [1 used]	Manual for Industrial Direct Fired Heaters.
Thermostats/Sensors
A/CP-DO-240-QC [2 used]	10K, Type II thermistor with 6" probe. 20' wire leads. (Replaces part# A/CP-DO-120-QC)
Transformers
1092TYPEF [1 used]	Ignition Transformer 120V, 180VA, Output 6000 Volts Used with direct fired heaters
BE161640GEK0018 [1 used]	TRANSFORMER - Low 40VA Voltage Transformer Used for 120v Primary and 24v Secondary.

Options

Part
AALARM	Audible Alarm, 120v,(Alarm sounds on flame failure).
Show parts
	SCE120LA3FP1B [1 used]	Sonalert, Pluggable 2900Hz 48-120VAC Loud Fast Pulse AX# A0017031
6631T18	Combustible Gas and Carbon Monoxide Detector 120VAC input. On-Board 10A, 250V Relay and 85db Audible Alarm. 150ppm CO, 17ppm H2, 5000 ppm Methane, 35ppm Propane. (HIC-822). 10,000 cubic feet recommended coverage per detector.
CODTIL	Detector/Alarm Interlock (By Others)
D4120-DST-1.5	Duct Mounted Smoke Detector For Direct Fired Heater. Complete with detector (D4120) and sampling tube (DST-1.5). Ships Loose.
Show parts
	D4120 [1 used]	Duct Mounted Smoke Detector For Direct Fired Heater. Air Velocity 100 to 4000 FPM, Humidity Range 0 to 95 Percentage RH, Current Consumption Alarm 125 Milliamps, Current Consumption Standby 21 Milliamps @ 24vdc, Alarm Auxiliary Contact Current @ 250 VAC 10 Amps, Alarm Auxiliary Contact Current @ 30 VDC 10 Amps, Ambient Temperature Limit -4 to 158 Degrees Fahrenheit, Photoelectric, Base.
	DST-1.5 [1 used]	Duct Mounted Smoke Detector Sampling Tube, Duct Width 1 to 2 Feet, Metal, For Duct Mounted Smoke Detector, used with D4120 Detector.
SMDTIL	Smoke Detector Interlock (By Others)
XBIND4	Extra Set of V-Belts For Size Four Industrial. Only to be ordered as fan option at time fan is ordered.
EGL-4	Size 4 Industrial Heater Extended Grease Lines
Show parts
	ALUM TUBING [1.1 used]	1/4" X 10' aluminum tubing, used on extended grease lines.
	0402419 [2 used]	1/4" MPT x 1/8" FPT Stl Strait Expander 5405 Series - Used on extended grease lines. Screws into pillow block bearing.
	66570 [2 used]	1/8" Coupler - Used on extended grease lines. Secures zerk fitting to sheet metal housing.
	60102 [2 used]	1/8" NPT Straight Standard Zerk Fitting - Used on extended grease lines.
	440576-131280 [4 used]	Brass 90(1/4"Tube OD x 1/8" MPT 2000psi Brass 90Deg SELFALIGN Elbow). Used as 90 deg fitting on extended grease lines.
CABHTR100WNC	Control panel enclosure heater, includes 100w, 120v heater. Recommended for winter design temperature less than 0°F. Operates on PCB controls in IBT Single Modules or RTU
Show parts
	D43/5200/015018 [1 used]	Enclosure heater, stainless steel sheath w/ plated fins. 100w @ 120v. 0.9 Amps. Replaces 450WSTPHTR
CABHTR200W	Control panel enclosure heater, includes 200w, 120v heater and thermostat (10 degree setting). Requires convenience outlet option (power by others). Recommended for winter design temperature less than 0°F. - Old Controls
Show parts
	D43/5200/015018 [1 used]	Enclosure heater, stainless steel sheath w/ plated fins. 100w @ 120v. 0.9 Amps. Replaces 450WSTPHTR
	T6031A1136 [1 used]	Intake Air Thermostat For Commercial Heaters - Honeywell Temp Control Used, temp range of -30 to 90 deg f and 5' capillary tube.
BHE	Box Hanging Eyes (set of 4) for Industrial Direct Fired Heaters (Sizes 2-8)
Show parts
	85000.004 [4 used]	PLATE, Industrial Box Style Lifting Eye 3/8" Used on Size 2-8 Horizontal Units.
NON SILICONE	Fan housing assembled without the use of silicone caulk. Primarily used for paint booth applications. Use Acrylic Latex Caulk , P/N A0011848.
POC	Proof of closure option for industrial direct fired heaters. One motorized valve must be included in gas manifold.
CINSUL-4	Size 4 Industrial Heater Casing Insulation with Steel Liner
FLINSUL-4	Size 4 Industrial Heater Floor Insulation with Steel Liner
DNDISINDH4-30-LR	Down Discharge Construction Size 4 Horizontal Industrial With 30" Blowers Left to Right Discharge
Show parts
	M4103H1I [1 used]	ELECTRICAL CONTROL PANEL FOR MOUNTING CONTROL COMPONENTS IN VESTIBULE FOR SIZE 4 & 8 HORIZONTAL INDUSTRIAL UNITS WITH LEFT TO RIGHT AIRFLOW.
	M400055W [1 used]	FRONT CORNER WALL PANEL WITH BLOWER DOOR JAMB.
	M4063H1W [1 used]	Intake panel bottom used in size 4 industrial horizontal industrial units
	M4061H1W [1 used]	Intake panel top used in size 4 industrial horizontal industrial units H1, H2, H3
	M4032H2B [2 used]	M4 Discharge flange used with Industrial Horizontal Units with 30" or (2) 30" blower and down discharge
	M4031H2B [2 used]	M4 Discharge flange used with Industrial Horizontal Units with 30" or (2) 30" blower and down discharge
	M300047R [2 used]	ROOF PANEL CONROL SIDE SIZE 3, BOTH SIDES SIZE 4. INDUSTRIAL DIRECT FIRED HEATER 44.42 x 103.16 x 18 GA.
	M400078R [1 used]	ROOF PANELS (1 REQUIRED) FOR SIZE 4 INDUSTRIAL DIRECT FIRED HEATER 30.82 x 102.69 x 18 GA.
	M4047H1W [1 used]	WALL PANEL, CORNER BACK SIDE 18GA G90, 15.56W X 28.5W X 62H
	M4052H2W [1 used]	WALL PANEL, DISCHARGE END MIDDLE, USED ON SIZE 4 AND SIZE 8 HORIZONTAL INDUSTRIAL UNITS WITH DOWN DISCHARGE WITHOUT AN INTERNAL DAMPER.
	M4057H1W [1 used]	WALL PANEL, DOOR DIVIDER H1, H2, H3
	M4058H1W [1 used]	WALL PANEL, INTAKE END H1, H2, H3
	M4044H1W [1 used]	WALL PANEL, INTAKE END LH, CONTAINS PILOT ACCESS OPENING, 43.13W X 62H
DNDISINDH4-30-RL	Down Discharge Construction Size 4 Horizontal Industrial With 30" Blowers Right to Left Discharge
Show parts
	M400056W [1 used]	FRONT CORNER WALL PANEL WITH BLOWER DOOR JAMB. H4, H5, H6
	M4063H1W [1 used]	Intake panel bottom used in size 4 industrial horizontal industrial units
	M4062H4W [1 used]	Intake panel top used in size 4 industrial horizontal industrial units H4, H5, H6
	M4032H2B [2 used]	M4 Discharge flange used with Industrial Horizontal Units with 30" or (2) 30" blower and down discharge
	M4031H2B [2 used]	M4 Discharge flange used with Industrial Horizontal Units with 30" or (2) 30" blower and down discharge
	M300047R [2 used]	ROOF PANEL CONROL SIDE SIZE 3, BOTH SIDES SIZE 4. INDUSTRIAL DIRECT FIRED HEATER 44.42 x 103.16 x 18 GA.
	M400078R [1 used]	ROOF PANELS (1 REQUIRED) FOR SIZE 4 INDUSTRIAL DIRECT FIRED HEATER 30.82 x 102.69 x 18 GA.
	M400294I [1 used]	Vestibule electrical control panel used on size 4 and 8 industrial horizontal units H4, H5, H5I, H6
	M4048H1W [1 used]	WALL PANEL, CORNER BACK SIDE 18GA G90, H4, H5, H6
	M4052H2W [1 used]	WALL PANEL, DISCHARGE END MIDDLE, USED ON SIZE 4 AND SIZE 8 HORIZONTAL INDUSTRIAL UNITS WITH DOWN DISCHARGE WITHOUT AN INTERNAL DAMPER.
	M400289W [1 used]	WALL PANEL, DOOR DIVIDER H4, H5, H6
	M4059H4W [1 used]	WALL PANEL, INTAKE END H4, H5, H6
	M4045H1W [1 used]	WALL PANEL, INTAKE END, CONTAINS PILOT ACCESS OPENING H4, H5, H6
DNDISINDH4-30IDD	Down Discharge Construction Size 4 Horizontal Industrial With 30" Blowers and Internal Discharge Dampers
Show parts
	M4074H2W [1 used]	ACCESS PANEL INTERNAL DISCHARGE DAMPER SIZE 4 AND 8 INDUSTRIAL HORIZONTAL UNITS WITH 30" BLOWERS
	M4038H2B [2 used]	Discharge flange with internal used on size 4 and size 8 industrial horizontal units with 30" blower H2I, H5I
	M4037H2B [2 used]	Discharge flange with internal used on size 4 and size 8 industrial horizontal units with 30" blower H2I, H5I
	M4036H1B [1 used]	Floor panel middle used on size 4 and size 8 industrial horizontal units with 30" blower H2I, H5I
	M4112H2I [1 used]	Frame housing cover for internal damper used on size 4 and size 8 industrial horizontal units with 30" blower H2I, H5I
	M4099H2B [2 used]	Frame part to house internal damper used on size 4 and size 8 industrial horizontal units with 30" blower H2I, H5I
	M4098H2B [2 used]	Frame part to house internal damper used on size 4 and size 8 industrial horizontal units with 30" blower H2I, H5I
	M4032H2B [-1 used]	M4 Discharge flange used with Industrial Horizontal Units with 30" or (2) 30" blower and down discharge
	M4031H2B [-1 used]	M4 Discharge flange used with Industrial Horizontal Units with 30" or (2) 30" blower and down discharge
	M4052H2W [-1 used]	WALL PANEL, DISCHARGE END MIDDLE, USED ON SIZE 4 AND SIZE 8 HORIZONTAL INDUSTRIAL UNITS WITH DOWN DISCHARGE WITHOUT AN INTERNAL DAMPER.
	M4073H2W [1 used]	WALL PANEL, DISCHARGE WALL, ABOVE INTERNAL DISCHARGE ACCESS, SIZE 4 AND 8 HORIZONTAL INDUSTRIAL UNITS WITH 30" BLOWERS
SDDISINDH4-30-LR	Side Discharge Construction Size 4 Horizontal Industrial With 30" Blowers Left to Right Discharge
Show parts
	M4103H1I [1 used]	ELECTRICAL CONTROL PANEL FOR MOUNTING CONTROL COMPONENTS IN VESTIBULE FOR SIZE 4 & 8 HORIZONTAL INDUSTRIAL UNITS WITH LEFT TO RIGHT AIRFLOW.
	M4014H1B [1 used]	Floor panel middle used on size 4 and size 8 industrial horizontal units with 30" blower H1, H3, H4, H6
	M400055W [1 used]	FRONT CORNER WALL PANEL WITH BLOWER DOOR JAMB.
	M4063H1W [1 used]	Intake panel bottom used in size 4 industrial horizontal industrial units
	M4061H1W [1 used]	Intake panel top used in size 4 industrial horizontal industrial units H1, H2, H3
	M300047R [2 used]	ROOF PANEL CONROL SIDE SIZE 3, BOTH SIDES SIZE 4. INDUSTRIAL DIRECT FIRED HEATER 44.42 x 103.16 x 18 GA.
	M400078R [1 used]	ROOF PANELS (1 REQUIRED) FOR SIZE 4 INDUSTRIAL DIRECT FIRED HEATER 30.82 x 102.69 x 18 GA.
	M4051H1W [1 used]	WALL PANEL, ABOVE SIDE BLOWER DISCHARGE SIZE 4 AND SIZE 8 INDUSTRIAL HORIZONTAL UNITS.
	M4065H1W [1 used]	WALL PANEL, BELOW SIDE BLOWER DISCHARGE SIZE 4 AND SIZE 8 INDUSTRIAL HORIZONTAL UNITS.
	M4047H1W [1 used]	WALL PANEL, CORNER BACK SIDE 18GA G90, 15.56W X 28.5W X 62H
	M4057H1W [1 used]	WALL PANEL, DOOR DIVIDER H1, H2, H3
	M4058H1W [1 used]	WALL PANEL, INTAKE END H1, H2, H3
	M4044H1W [1 used]	WALL PANEL, INTAKE END LH, CONTAINS PILOT ACCESS OPENING, 43.13W X 62H
SDDISINDH4-30-RL	Side Discharge Construction Size 4 Horizontal Industrial With 30" Blowers Right to Left Discharge
Show parts
	M4014H1B [1 used]	Floor panel middle used on size 4 and size 8 industrial horizontal units with 30" blower H1, H3, H4, H6
	M400056W [1 used]	FRONT CORNER WALL PANEL WITH BLOWER DOOR JAMB. H4, H5, H6
	M4063H1W [1 used]	Intake panel bottom used in size 4 industrial horizontal industrial units
	M4062H4W [1 used]	Intake panel top used in size 4 industrial horizontal industrial units H4, H5, H6
	M300047R [2 used]	ROOF PANEL CONROL SIDE SIZE 3, BOTH SIDES SIZE 4. INDUSTRIAL DIRECT FIRED HEATER 44.42 x 103.16 x 18 GA.
	M400078R [1 used]	ROOF PANELS (1 REQUIRED) FOR SIZE 4 INDUSTRIAL DIRECT FIRED HEATER 30.82 x 102.69 x 18 GA.
	M400294I [1 used]	Vestibule electrical control panel used on size 4 and 8 industrial horizontal units H4, H5, H5I, H6
	M4051H1W [1 used]	WALL PANEL, ABOVE SIDE BLOWER DISCHARGE SIZE 4 AND SIZE 8 INDUSTRIAL HORIZONTAL UNITS.
	M4065H1W [1 used]	WALL PANEL, BELOW SIDE BLOWER DISCHARGE SIZE 4 AND SIZE 8 INDUSTRIAL HORIZONTAL UNITS.
	M4048H1W [1 used]	WALL PANEL, CORNER BACK SIDE 18GA G90, H4, H5, H6
	M400289W [1 used]	WALL PANEL, DOOR DIVIDER H4, H5, H6
	M4059H4W [1 used]	WALL PANEL, INTAKE END H4, H5, H6
	M4045H1W [1 used]	WALL PANEL, INTAKE END, CONTAINS PILOT ACCESS OPENING H4, H5, H6
UPDISINDH4-30-LR	Up Discharge Construction Size 4 Horizontal Industrial With 30" Blowers Left to Right Discharge
Show parts
	M4108H3I [1 used]	Blower discharge extension used on size 4 and 8 industrial horizontal units with 30" blowers H3 and H6
	M4107H3I [1 used]	Blower discharge extension used on size 4 and 8 industrial horizontal units with 30" blowers H3 and H6
	M4103H1I [1 used]	ELECTRICAL CONTROL PANEL FOR MOUNTING CONTROL COMPONENTS IN VESTIBULE FOR SIZE 4 & 8 HORIZONTAL INDUSTRIAL UNITS WITH LEFT TO RIGHT AIRFLOW.
	M4014H1B [1 used]	Floor panel middle used on size 4 and size 8 industrial horizontal units with 30" blower H1, H3, H4, H6
	M400055W [1 used]	FRONT CORNER WALL PANEL WITH BLOWER DOOR JAMB.
	M4063H1W [1 used]	Intake panel bottom used in size 4 industrial horizontal industrial units
	M4061H1W [1 used]	Intake panel top used in size 4 industrial horizontal industrial units H1, H2, H3
	M300079R [1 used]	Roof panel rear side for size 3 unit with 25" blower and up diischarge. 15.63 x 100.31 x 18 GA.
	M4096H3R [1 used]	ROOF PANELS (1 REQUIRED) FOR SIZE 4 AND 8 INDUSTRIAL DIRECT FIRED HEATER UP DISCHARGE WITH 30" BLOWER
	M4081H3R [1 used]	ROOF PANELS (1 REQUIRED) FOR SIZE 4 AND 8 INDUSTRIAL DIRECT FIRED HEATER UP DISCHARGE WITH 30" BLOWER
	M4077H3R [1 used]	ROOF PANELS (1 REQUIRED) FOR SIZE 4 AND 8 INDUSTRIAL DIRECT FIRED HEATER UP DISCHARGE WITH 30" BLOWER
	M4047H1W [1 used]	WALL PANEL, CORNER BACK SIDE 18GA G90, 15.56W X 28.5W X 62H
	M4052H2W [1 used]	WALL PANEL, DISCHARGE END MIDDLE, USED ON SIZE 4 AND SIZE 8 HORIZONTAL INDUSTRIAL UNITS WITH DOWN DISCHARGE WITHOUT AN INTERNAL DAMPER.
	M4057H1W [1 used]	WALL PANEL, DOOR DIVIDER H1, H2, H3
	M4058H1W [1 used]	WALL PANEL, INTAKE END H1, H2, H3
	M4044H1W [1 used]	WALL PANEL, INTAKE END LH, CONTAINS PILOT ACCESS OPENING, 43.13W X 62H
UPDISINDH4-30-RL	Up Discharge Construction Size 4 Horizontal Industrial With 30" Blowers Right to Left Discharge
Show parts
	M4108H3I [1 used]	Blower discharge extension used on size 4 and 8 industrial horizontal units with 30" blowers H3 and H6
	M4107H3I [1 used]	Blower discharge extension used on size 4 and 8 industrial horizontal units with 30" blowers H3 and H6
	M4014H1B [1 used]	Floor panel middle used on size 4 and size 8 industrial horizontal units with 30" blower H1, H3, H4, H6
	M400056W [1 used]	FRONT CORNER WALL PANEL WITH BLOWER DOOR JAMB. H4, H5, H6
	M4063H1W [1 used]	Intake panel bottom used in size 4 industrial horizontal industrial units
	M4062H4W [1 used]	Intake panel top used in size 4 industrial horizontal industrial units H4, H5, H6
	M300079R [1 used]	Roof panel rear side for size 3 unit with 25" blower and up diischarge. 15.63 x 100.31 x 18 GA.
	M4096H3R [1 used]	ROOF PANELS (1 REQUIRED) FOR SIZE 4 AND 8 INDUSTRIAL DIRECT FIRED HEATER UP DISCHARGE WITH 30" BLOWER
	M4081H3R [1 used]	ROOF PANELS (1 REQUIRED) FOR SIZE 4 AND 8 INDUSTRIAL DIRECT FIRED HEATER UP DISCHARGE WITH 30" BLOWER
	M4077H3R [1 used]	ROOF PANELS (1 REQUIRED) FOR SIZE 4 AND 8 INDUSTRIAL DIRECT FIRED HEATER UP DISCHARGE WITH 30" BLOWER
	M400294I [1 used]	Vestibule electrical control panel used on size 4 and 8 industrial horizontal units H4, H5, H5I, H6
	M4048H1W [1 used]	WALL PANEL, CORNER BACK SIDE 18GA G90, H4, H5, H6
	M4052H2W [1 used]	WALL PANEL, DISCHARGE END MIDDLE, USED ON SIZE 4 AND SIZE 8 HORIZONTAL INDUSTRIAL UNITS WITH DOWN DISCHARGE WITHOUT AN INTERNAL DAMPER.
	M400289W [1 used]	WALL PANEL, DOOR DIVIDER H4, H5, H6
	M4059H4W [1 used]	WALL PANEL, INTAKE END H4, H5, H6
	M4045H1W [1 used]	WALL PANEL, INTAKE END, CONTAINS PILOT ACCESS OPENING H4, H5, H6
Cooling Interlock	Cooling Interlock Between Remote Panel and Heater
CIR-IN	Cooling Interlock Relay Mounted in Unit - After Air Proving and Intake Air Stat.
Show parts
	34.110.0184.0 [1 used]	RELAY - Used with part number 34.110.0147.0. (120VAC, 10 Amps) DPDT. (Clion = HHC68A-2Z-120VAC-T+LED), with LED indicator light with AgCe contacts rated to 15A.
	34.110.0147.0 [1 used]	RELAY Socket PTF08A - 10 Amp Contacts, Plug in style. Used with part number 34.110.0146.0, 34.110.0188.0, or 34.110.0168.0. Coil Terminals = 7&8. (Contact 1: Com=5, NC=1, NO=3) (Contact 2: Com=6, NC=2, NO=4)
A30SDAD-R	180° Side Discharge Air Diffuser A30
A30DDAD3W	3-Way Down Discharge Air Diffuser A30
A30DDAD4W	4-Way Down Discharge Air Diffuser A30
A30DDAD	45° Down Discharge Air Diffuser A30
NON_FUSED_DISC_IND_SEP120	Non-Fused Disconnect Switch for Industrial Make Up Air Units, Sep 120v Connection.
NON_FUSED_DISC_IND_SP	Non-Fused Disconnect Switch for Industrial Make Up Air Units, Single Point Connection.
PRESSGA15	Gas Pressure Gauge, 0-15PSI, 2.5" Diameter, 1/4" Thread Size
PRESSGA35	Gas Pressure Gauge, 0-35", 2.5" Diameter, 1/4" Thread Size
PRESSGA5	Gas Pressure Gauge, 0-5#, 2.5" Diameter, 1/4" Thread Size
PRESSGA-5-0+15	Gas Pressure Gauge, -5 to +15 Inches Wc., 2.5" Diameter, 1/4" Thread Size
PRESSGA35	Gas Pressure Gauge, 0-35", 2.5" Diameter, 1/4" Thread Size
PRESSGA15	Gas Pressure Gauge, 0-15PSI, 2.5" Diameter, 1/4" Thread Size
GMH-A4-4-4	High Gas Pressure Switch (1" - 20" WC) Factory set at 8" w.c. Replaces part HGP-A.
LGPSO	Low Pressure Gas Switch (1" - 6" WC) Factory set at 2" w.c.
Show parts
	GML-A4-4-4 [1 used]	LOW GAS PRESSURE SWITCH - Low Pressure Gas Switch (1" - 20" WC) Factory set at 2" w.c. Replaces part LGP-A.
Gas Strainer 1 1/2"	Ship Loose Gas Strainer. To be installed upstream of unit connection. 1 1/2" Connection
Show parts
	4417K67 [1 used]	Gas Y-Strainer, 100 Micron Mesh, 1-1/2" NPT
Gas Strainer 1 1/4"	Ship Loose Gas Strainer. To be installed upstream of unit connection. 1 1/4" Connection
Show parts
	4417K66 [1 used]	Gas Y-Strainer, 100 Micron Mesh, 1-1/4" NPT
Gas Strainer 1"	Ship Loose Gas Strainer. To be installed upstream of unit connection. 1" Connection
Show parts
	4417K65 [1 used]	Gas Y-Strainer, 100 Micron Mesh, 1" NPT
Gas Strainer 2"	Ship Loose Gas Strainer. To be installed upstream of unit connection. 2" Connection
Show parts
	4417K68 [1 used]	Gas Y-Strainer, 100 Micron Mesh, 2" NPT
Gas Strainer 3/4"	Ship Loose Gas Strainer. To be installed upstream of unit connection. 3/4" Connection
Show parts
	4417K64 [1 used]	Gas Y-Strainer, 100 Micron Mesh, 3/4" NPT
CLCOMM_REV04	CASLink building monitoring system communications module. Requires internet & field wired ethernet connection or 3G cellular service. Includes Rev 3 Comm Module, RJ45 to modbus converter, 3 FT cat5 cable, and 1 FT of shielded twisted pair.
Show parts
	COMM01_rev4 [1 used]	CASLink Building Monitoring system communications module. Includes monitoring provisions for CORE interlock fire network and hood control network. Requires internet connection. Should be used for an ethernet length of 100ft. or greater.
	CAT5_Regular_3 [1 used]	CAT-5E CABLE - 3 Foot.
	MDP18-24A-1C [1 used]	DIN rail power supply 100-240VAC input 24 VDC, 18 Watts Replaces: DR-15-24
	88760 [1 used]	Multi-Conductor - Single Shielded Twisted Pair Cable, 18 AWG stranded (19x30) TC conductors, plenum, FEP insulation, overall shield (100% coverage), 20 AWG stranded TC drain wire, FEP jacket. Priced per foot. For use with CORE Interlock Network, light dimming 0-10VDC reference signal, and PWM signal from ECPM03 to ECM.
DDC-IP BACnet Monitoring	Remote IP BACnet monitoring for supply fans.
Show parts
	CAS_BACNET_GATEWAY_FAN [1 used]	BMS Gateway for BACNET MS/TP or BACNET IP. Includes CAS_GATEWAY circuit board and Protocessor BACnet interface. For use with PEM mounting standoffs. Not rated for use outside of an enclosure. When ordered as a part, specify MS/TP or IP in programmable part notes. PART REQUIRES PROGRAMMING!
	CAT5_Regular_1 [1 used]	CAT-5E CABLE - 1.0 Foot.
	RJ45_MODBUS_CONVERTER [1 used]	RJ45 TO SHIELDED TWISTED MODBUS CONVERTER DIN RAIL MOUNTED PCB
	CELLULAR VERIZON DATA- 1 YR [1 used]	VERIZON DATA FOR 1 YEAR. FOR ONLINE STORE ORDERING ONLY.
DDC-MSTP BACnet Monitoring	Remote MSTP BACnet monitoring
Show parts
	CAS_BACNET_GATEWAY_FAN [1 used]	BMS Gateway for BACNET MS/TP or BACNET IP. Includes CAS_GATEWAY circuit board and Protocessor BACnet interface. For use with PEM mounting standoffs. Not rated for use outside of an enclosure. When ordered as a part, specify MS/TP or IP in programmable part notes. PART REQUIRES PROGRAMMING!
	CAT5_Regular_1 [1 used]	CAT-5E CABLE - 1.0 Foot.
Dry Mode	Dry Mode
Show parts
	RTUA/RH3-CP-D [2 used]	Duct RHP Temperature and Humidity Transmitter. 3% Accuracy.
	34.110.0184.0 [1 used]	RELAY - Used with part number 34.110.0147.0. (120VAC, 10 Amps) DPDT. (Clion = HHC68A-2Z-120VAC-T+LED), with LED indicator light with AgCe contacts rated to 15A.
	34.110.0147.0 [1 used]	RELAY Socket PTF08A - 10 Amp Contacts, Plug in style. Used with part number 34.110.0146.0, 34.110.0188.0, or 34.110.0168.0. Coil Terminals = 7&8. (Contact 1: Com=5, NC=1, NO=3) (Contact 2: Com=6, NC=2, NO=4)
FECONTAAFS	Field Wired Exhaust Contactor After Airflow Switch. Rated 23 Amps. Starts up to (2) Single Phase Motors. 2HP max. 115V, 3HP max. 240V. Starts one Three Phase Motor. 5HP max. 208V, 7.5HP 230v, 15HP max. 460V, 15HP max. 575V or (4) Dry Interlocks. Overload not Included
Show parts
	100-C23D10 [1 used]	Contactor - 120V, 50/60Hz Coil, Rated for 23 AMPs. Used only with Rockwell 193-T1A System Overloads.
FECONTBAFS	Field Wired Exhaust Contactor Before Airflow Switch. Rated 23 Amps. Starts up to (2) Single Phase Motors. 2HP max. 115V, 3HP max. 240V. Starts one Three Phase Motor. 5HP max. 208V, 7.5HP max 230v, 15HP max. 460V. Overload not Included
Show parts
	100-C23D10 [1 used]	Contactor - 120V, 50/60Hz Coil, Rated for 23 AMPs. Used only with Rockwell 193-T1A System Overloads.
FECONTBAFS	Field Wired Exhaust Contactor Before Airflow Switch. Rated 23 Amps. Starts up to (2) Single Phase Motors. 2HP max. 115V, 3HP max. 240V. Starts one Three Phase Motor. 5HP max. 208V, 7.5HP max 230v, 15HP max. 460V. Overload not Included
Show parts
	100-C23D10 [1 used]	Contactor - 120V, 50/60Hz Coil, Rated for 23 AMPs. Used only with Rockwell 193-T1A System Overloads.
Exhaust on Fire	Exhaust on Fire
EXHRELAYBAFS	Exhaust Relay Before Airflow Switch. Provides 2 sets of NO to be used as a start command interlock for exhaust fans.
Show parts
	34.110.0184.0 [1 used]	RELAY - Used with part number 34.110.0147.0. (120VAC, 10 Amps) DPDT. (Clion = HHC68A-2Z-120VAC-T+LED), with LED indicator light with AgCe contacts rated to 15A.
	34.110.0190.0 [2 used]	RELAY SECURITY CLIP. Used with part number 34.110.0147.0
	34.110.0147.0 [1 used]	RELAY Socket PTF08A - 10 Amp Contacts, Plug in style. Used with part number 34.110.0146.0, 34.110.0188.0, or 34.110.0168.0. Coil Terminals = 7&8. (Contact 1: Com=5, NC=1, NO=3) (Contact 2: Com=6, NC=2, NO=4)
LFS	Low Fire Start. Allows the burner circuit to energize when the modulation control is in a low fire position.
MAN RES FSC	Manual reset of flame safety controller. Used to meet Canada requirement. Flame safety will not reset on cycle of power. Dips 1,2,3,5 closed, 4, 6 open standard settings.
OCCUPIED SCHEDULING	Occupied Scheduling Defaulted for IBT/RTU.
OPPSIDE-IH-CTRLS	Mount motor and controls on opposite side of heaters with single blowers
INSUEXPV	Supply and exhaust (exhaust by others) proving for industrial make up air units. Includes timed relay, requires field supplied exhaust interlock.
Show parts
	TIMER182 [1 used]	Delay on break (post purge)/delay on make electronic timer, two changeover relays rated at 2,00VA AC, 192W DC, 0.1 second to 10 minute range, 12-240V AC/DC (AC 50/60hz), green LED input indicator, red LED output indicator, DIN rail mount.
1 Stage Cooling Terminals (Cooling by Others)	1 Stage Cooling Terminals (Cooling by Others)
2 Stage Cooling Terminals (Cooling by Others)	2 Stage Cooling Terminals (Cooling by Others)
CLOGFILTHMI	Clogged Filter Switch with Notification on HMI
Show parts
	RFS-4100-078 [1 used]	AIR FLOW SWITCH - Used for IBT air proving switch and clogged filter switch option. Factory set @ .25", adjustable.
CLOGFILT	Clogged Filter Switch with Light on Remote Panel
Show parts
	RFS-4100-078 [1 used]	AIR FLOW SWITCH - Used for IBT air proving switch and clogged filter switch option. Factory set @ .25", adjustable.
PBCLOGFILT	Clogged Filter Switch with Light on Paint Booth Control Panel
Show parts
	RFS-4100-078 [1 used]	AIR FLOW SWITCH - Used for IBT air proving switch and clogged filter switch option. Factory set @ .25", adjustable.
Control Vestibule LED Lights	Control Vestibule LED Lights Used on Industrial Units.
Show parts
	LED Strip [1 used]	LED Strip Light 3 feet 24V DC.
	BZ-2RQ1-A2 [1 used]	Switch, overtravel switch for door sense, single pole, double throw. Screw terminals
	91735A146 [4 used]	Type 316 Stainless Steel Pan Head Phillips Machine Screw, 6-32 Thread, 3/8" Length.
CVOUTLET	GFCI 15 amp Convenience Outlet For Heater Enclosure. Power supply by others - Includes receptacle and J box.
INDPCVOUTLET	GFCI 15 amp Powered Convenience Outlet For Industrial units with 208/230/460 power. Includes receptacle, jbox, cover and transformer. Not available with ship loose vfd.
Show parts
	SU201M-K15 [1 used]	CIRCUIT BREAKER - 15 AMP Circuit Breaker Used for Indirect Heaters. Trip Curve D. UL489.
	GFR 5252 [1 used]	DCO 120/15A #1595 GFCI Receptacle
	8012A [1 used]	J-BOX - SWITCH BOX - CY X 1/2.
	B2K0-2270-GAH [1 used]	TRANSFORMER - Micron 2000va Transformer Used on RTU's with convenience outlets. Voltage inputs are 208/230/480.
N.O. Contacts	Extra set of N.O. contacts on supply starter.
Purge mode	Purge option selected. Allows the user to purge the space by manually activtating on the HMI.
Show parts
	RTUA/RH3-CP-D [1 used]	Duct RHP Temperature and Humidity Transmitter. 3% Accuracy.
	34.110.0184.0 [1 used]	RELAY - Used with part number 34.110.0147.0. (120VAC, 10 Amps) DPDT. (Clion = HHC68A-2Z-120VAC-T+LED), with LED indicator light with AgCe contacts rated to 15A.
	34.110.0147.0 [1 used]	RELAY Socket PTF08A - 10 Amp Contacts, Plug in style. Used with part number 34.110.0146.0, 34.110.0188.0, or 34.110.0168.0. Coil Terminals = 7&8. (Contact 1: Com=5, NC=1, NO=3) (Contact 2: Com=6, NC=2, NO=4)
Shaft Grounding Ring Option	Shaft Grounding Ring Option
A30DDD-R INS	External Down Discharge Insulated Damper for size 4 horizontal industrial units with 30" blowers. Includes actuator. Insulated blades and frame. Thermally broken blades. Non-stock option, lead time 6 weeks.
Show parts
	AFBUP-S [1 used]	ACTUATOR - AF Series (DCA) Spring Return, 180 in-lb torque. Running time <75 sec. (on/off) & <60 sec (spring), 8.5VA , adjustable end stop 35-95deg; Angle rotation, 1/2" to 1.05" Shaft dia, Visual position indicator, Control direction CW. Direct Replacement for AF120-S.
	IND4-30DD INS [1 used]	External Discharge Insulated Damper for size 4 industrial units with 30" blowers, requires NFBUP-S actuator, sold separately. Insulated blades and frame. Thermally broken blades. Non-stock option, lead time 8 weeks.
A30DDS-R INS	External Side Discharge Insulated Damper for size 4 Horizontal industrial units with 30" blowers. Includes actuator. Insulated blades and frame. Thermally broken blades. Non-stock option, lead time 6 weeks.
Show parts
	AFBUP-S [1 used]	ACTUATOR - AF Series (DCA) Spring Return, 180 in-lb torque. Running time <75 sec. (on/off) & <60 sec (spring), 8.5VA , adjustable end stop 35-95deg; Angle rotation, 1/2" to 1.05" Shaft dia, Visual position indicator, Control direction CW. Direct Replacement for AF120-S.
	ACTCOVER [1 used]	ACTUATOR COVER - Used on outdoor Industrial Heaters to protect damper actuators.
	IND4-30DD INS [1 used]	External Discharge Insulated Damper for size 4 industrial units with 30" blowers, requires NFBUP-S actuator, sold separately. Insulated blades and frame. Thermally broken blades. Non-stock option, lead time 8 weeks.
R4 ID INS	Size 4 Horizontal Industrial Heater Insulated Intake Damper. Includes Actuator. Non-stock option, lead time 6 weeks.
Show parts
	AFBUP-S [1 used]	ACTUATOR - AF Series (DCA) Spring Return, 180 in-lb torque. Running time <75 sec. (on/off) & <60 sec (spring), 8.5VA , adjustable end stop 35-95deg; Angle rotation, 1/2" to 1.05" Shaft dia, Visual position indicator, Control direction CW. Direct Replacement for AF120-S.
	ACTCOVER [1 used]	ACTUATOR COVER - Used on outdoor Industrial Heaters to protect damper actuators.
	IND4ID-INS [1 used]	Insulated intake damper for size 4 Horizontal Industrial Heater with 27" & 30" blower wheels, requires AFBUP-S actuator sold separately. Insulated blades and frame. Thermally broken blades. Non-stock option, lead time 6 weeks.
A30DD-DM	External Discharge CD60 Damper for size 4 industrial units with 30" blowers. Includes actuator.
Show parts
	AFBUP-S [1 used]	ACTUATOR - AF Series (DCA) Spring Return, 180 in-lb torque. Running time <75 sec. (on/off) & <60 sec (spring), 8.5VA , adjustable end stop 35-95deg; Angle rotation, 1/2" to 1.05" Shaft dia, Visual position indicator, Control direction CW. Direct Replacement for AF120-S.
	ACTCOVER [1 used]	ACTUATOR COVER - Used on outdoor Industrial Heaters to protect damper actuators.
	IND4-30DD [1 used]	External Discharge CD60 Damper for size 4 industrial units with 30" blowers, requires NFBUP-S actuator, sold separately.
A30DDD-R	External Down Discharge CD60 Damper for size 4 horizontal industrial units with 30" blowers. Includes actuator.
Show parts
	AFBUP-S [1 used]	ACTUATOR - AF Series (DCA) Spring Return, 180 in-lb torque. Running time <75 sec. (on/off) & <60 sec (spring), 8.5VA , adjustable end stop 35-95deg; Angle rotation, 1/2" to 1.05" Shaft dia, Visual position indicator, Control direction CW. Direct Replacement for AF120-S.
	IND4-30DD [1 used]	External Discharge CD60 Damper for size 4 industrial units with 30" blowers, requires NFBUP-S actuator, sold separately.
FIELDDMP(S)	Field Supplied Damper(s) Indicated By Others
A30DDI	Internal Down Discharge Damper for size 4 industrial horizontal units with 30" inch blowers. Includes actuator.
Show parts
	NFBUP-S [1 used]	ACTUATOR - NF Series (DCA) Spring Return, 90 in-lb torque. Running time <75 sec. (on/off) & <60 sec (spring), 24-240vac, 24-125vdc, 6.5VA @ 120vac, 95° Angle rotation, 1/2" to 1.05" Shaft dia, Visual position indicator, Control direction CW. Direct Replacement for NF120-S.
	IND48-30IDD [1 used]	Internal Down Discharge Damper for size 4 or 8 industrial horizontal units with 30" blowers, requires NFBUP-S actuator, sold separately.
A30DDS-R	External Side Discharge CD60 Damper for size 4 Horizontal industrial units with 30" blowers. Includes actuator.
Show parts
	AFBUP-S [1 used]	ACTUATOR - AF Series (DCA) Spring Return, 180 in-lb torque. Running time <75 sec. (on/off) & <60 sec (spring), 8.5VA , adjustable end stop 35-95deg; Angle rotation, 1/2" to 1.05" Shaft dia, Visual position indicator, Control direction CW. Direct Replacement for AF120-S.
	ACTCOVER [1 used]	ACTUATOR COVER - Used on outdoor Industrial Heaters to protect damper actuators.
	IND4-30DD [1 used]	External Discharge CD60 Damper for size 4 industrial units with 30" blowers, requires NFBUP-S actuator, sold separately.
R4 ID	Size 4 Horizontal Industrial Heater Intake Damper. Includes Actuator.
Show parts
	AFBUP-S [1 used]	ACTUATOR - AF Series (DCA) Spring Return, 180 in-lb torque. Running time <75 sec. (on/off) & <60 sec (spring), 8.5VA , adjustable end stop 35-95deg; Angle rotation, 1/2" to 1.05" Shaft dia, Visual position indicator, Control direction CW. Direct Replacement for AF120-S.
	ACTCOVER [1 used]	ACTUATOR COVER - Used on outdoor Industrial Heaters to protect damper actuators.
	IND4ID [1 used]	Intake damper for size 4 Horizontal Industrial Heater with 27" & 30" blower wheels, requires AFBUP-S actuator sold separately.
R4 ID-SL	Size 4 Horizontal Industrial Heater Intake Damper. Includes Actuator. SHIPS LOOSE For Mounting at Building Wall.
Show parts
	AFBUP-S [1 used]	ACTUATOR - AF Series (DCA) Spring Return, 180 in-lb torque. Running time <75 sec. (on/off) & <60 sec (spring), 8.5VA , adjustable end stop 35-95deg; Angle rotation, 1/2" to 1.05" Shaft dia, Visual position indicator, Control direction CW. Direct Replacement for AF120-S.
	ACTCOVER [1 used]	ACTUATOR COVER - Used on outdoor Industrial Heaters to protect damper actuators.
	IND4ID [1 used]	Intake damper for size 4 Horizontal Industrial Heater with 27" & 30" blower wheels, requires AFBUP-S actuator sold separately.
A30DDU-R	Ship Loose External Up Discharge CD60 Damper for size 4 horizontal industrial units with 30" blowers. Includes actuator.
Show parts
	AFBUP-S [1 used]	ACTUATOR - AF Series (DCA) Spring Return, 180 in-lb torque. Running time <75 sec. (on/off) & <60 sec (spring), 8.5VA , adjustable end stop 35-95deg; Angle rotation, 1/2" to 1.05" Shaft dia, Visual position indicator, Control direction CW. Direct Replacement for AF120-S.
	ACTCOVER [1 used]	ACTUATOR COVER - Used on outdoor Industrial Heaters to protect damper actuators.
	IND4-30DD [1 used]	External Discharge CD60 Damper for size 4 industrial units with 30" blowers, requires NFBUP-S actuator, sold separately.
PB-VFD-BSPC-AB	Auto Balance Exhaust VFD Static Pressure Control (preset to: -0.01 and 0.02)
Show parts
	8164 [50 used]	1/4" Nylon Tubing - Used with the Modular Make-Up Air Units A1-D, A2-D, A3-D, A4-D, A5-D and the NHMUA1, NHMUA2, NHMUA3, AI (Price Per Foot). Type 12.
	88130 [1 used]	1/4" Plastic Union Elbow for connecting airflow tubing to airflow probes (17045 & 17045A).
	17045 [1 used]	Airflow Switch Components Cleveland Controls Airflow Probe 2".
	A3300-0-LT [1 used]	Photohelic pressure differential guage (gauge only, accessories listed below), dual relay, pressure range of -.25" w.c. to .25" w.c. low temperature version, standard 80/20 guage. "RPPHOTOHELIC" includes remote mounting box. "A-306" contains pressure kit.
	A24N20CLP [-1 used]	Remote panel enclosure 24"Hx20"Wx10.62"D
	A24N20 [1 used]	Remote panel enclosure 24"Hx20"Wx10.62"D with mounting hole for photohelic.
PB-BSPC-AB	Auto Balance Exhaust Static Pressure Controls, vfd not included (preset to: -0.01 and 0.02)
Show parts
	8164 [50 used]	1/4" Nylon Tubing - Used with the Modular Make-Up Air Units A1-D, A2-D, A3-D, A4-D, A5-D and the NHMUA1, NHMUA2, NHMUA3, AI (Price Per Foot). Type 12.
	88130 [1 used]	1/4" Plastic Union Elbow for connecting airflow tubing to airflow probes (17045 & 17045A).
	17045 [1 used]	Airflow Switch Components Cleveland Controls Airflow Probe 2".
	A3300-0-LT [1 used]	Photohelic pressure differential guage (gauge only, accessories listed below), dual relay, pressure range of -.25" w.c. to .25" w.c. low temperature version, standard 80/20 guage. "RPPHOTOHELIC" includes remote mounting box. "A-306" contains pressure kit.
	A24N20CLP [-1 used]	Remote panel enclosure 24"Hx20"Wx10.62"D
	A24N20 [1 used]	Remote panel enclosure 24"Hx20"Wx10.62"D with mounting hole for photohelic.
PB-VFD-RMP-MB	Manual Balance Exhaust VFD Control
PB-LC	Paint Booth Lighting Circuit Switch Only.
PB-LC-AO	Paint Booth Lighting Circuit Switch and Auto Off in Cure Mode.
PB-PURGE	Paint Booth Purge Cycle with Light
CONSERVETMR	Spray mode energy conservation timer, reduces cfm's if spray not active. Factory set for 5 minutes. Requires mau vfd.
Show parts
	TIMER182 [1 used]	Delay on break (post purge)/delay on make electronic timer, two changeover relays rated at 2,00VA AC, 192W DC, 0.1 second to 10 minute range, 12-240V AC/DC (AC 50/60hz), green LED input indicator, red LED output indicator, DIN rail mount.
ENAM-4	Tan Enamel Coating (exterior walls/roof) For Heaters with 27"-30" blower wheels, includes casing and intakes. Consult factory for other colors. Sherwin Williams p/n F75KXN5809-4347, (AX = A0006229)
NOSTOVVFD	No starter/overloads installed in unit, no vav profile package, includes VFD for soft start operation (ship loose is default).
Show parts
	RFS-4300-111 [1 used]	Low Air Flow Switch with a preset pressure of .15", non-adjustable, currently used with Industrial 100% outside air, used in obsolete two speed (low speed) and obsolete vav Industrial Heaters
NOSTOVECPM03	No starter/overloads installed in unit, vfd for soft start by others (ECPM03), no vav profile package provided.
Show parts
	RFS-4300-111 [1 used]	Low Air Flow Switch with a preset pressure of .15", non-adjustable, currently used with Industrial 100% outside air, used in obsolete two speed (low speed) and obsolete vav Industrial Heaters
NOSTOV	No starter/overloads installed in unit, non-fused disconnect switch, vfd for soft start by others, no vav profile package provided.
Show parts
	RFS-4300-111 [1 used]	Low Air Flow Switch with a preset pressure of .15", non-adjustable, currently used with Industrial 100% outside air, used in obsolete two speed (low speed) and obsolete vav Industrial Heaters
VAV-PWP4-DCV	Size 4 VAV Profile and Wiring Package, For Use With DCV.
Show parts
	NMQX24-MFT [1 used]	ACTUATOR - NM Series Direct Coupled Damper Actuator Non Spring Return, 12va, 70 in-lb torque, 2-10 vdc or 4-20ma control signal. Used on VAV bypass dampers.
	DDP-106-177 [1 used]	AIR FLOW SWITCH - Used with industrial two speed and industrial vav units. Factory set @ .15" to .65".
	S1A [1 used]	Auxiliary end switch for AM, GM, LM, NM series actuators, contains one spdt end switches, 3 amp (0.5a inductive) at 250v rating.
	BE141620GEK0032 [1 used]	TRANSFORMER - 120V-24V 20VA with QC's Prod. 50/60Hz
VAV-PWP4-DCV-MUA	Size 4 VAV Profile and Wiring Package, For Use With MUA Board and DCV.
Show parts
	AFX24SR [1 used]	Damper Actuator, spring return, 2-10 dc siganal, 24vac power supply. Same actuator as AFB24SR with 10ft A3 Cable.
VAV-PWP4-ND	Size 4 VAV Profile and Wiring Package. No VFD included
Show parts
	AMB24-3 [1 used]	Actuator used for floating point operation, 24vac power, 2.5 watts, 180 in-lb torque, 95 second opening time, 3ft connection cable, 1/2" conduit connections.
	DDP-106-177 [1 used]	AIR FLOW SWITCH - Used with industrial two speed and industrial vav units. Factory set @ .15" to .65".
	S1A [1 used]	Auxiliary end switch for AM, GM, LM, NM series actuators, contains one spdt end switches, 3 amp (0.5a inductive) at 250v rating.
	Kt10542 [1 used]	Flame limiting potentiometer used to limit high fire on some two speed and vav units. (Macola#261) 30-180 ohms.
	BE141620GEK0032 [1 used]	TRANSFORMER - 120V-24V 20VA with QC's Prod. 50/60Hz
VAV-PWP4-ND-NP	Size 4 VAV Profile and Wiring Package. No VFD included
Show parts
	AMB24-3 [1 used]	Actuator used for floating point operation, 24vac power, 2.5 watts, 180 in-lb torque, 95 second opening time, 3ft connection cable, 1/2" conduit connections.
	DDP-106-177 [1 used]	AIR FLOW SWITCH - Used with industrial two speed and industrial vav units. Factory set @ .15" to .65".
	S1A [1 used]	Auxiliary end switch for AM, GM, LM, NM series actuators, contains one spdt end switches, 3 amp (0.5a inductive) at 250v rating.
	BE141620GEK0032 [1 used]	TRANSFORMER - 120V-24V 20VA with QC's Prod. 50/60Hz
VAV-PWPH4-BSPC	Size 4 Horizontal Heater VAV Profile and Wiring Package w/ Building Static Pressure Control
Show parts
	NMQX24-MFT [1 used]	ACTUATOR - NM Series Direct Coupled Damper Actuator Non Spring Return, 12va, 70 in-lb torque, 2-10 vdc or 4-20ma control signal. Used on VAV bypass dampers.
	DDP-106-177 [1 used]	AIR FLOW SWITCH - Used with industrial two speed and industrial vav units. Factory set @ .15" to .65".
	S1A [1 used]	Auxiliary end switch for AM, GM, LM, NM series actuators, contains one spdt end switches, 3 amp (0.5a inductive) at 250v rating.
	RPPHOTOHELIC [1 used]	Photohelic remote panel, includes box, lid and 3300-0-LT Photohelic guage, A-306 air pressure kit sold separately
	A-306 [1 used]	Static Pressure Kit for Photohelic, contains 1/8" id tubing, fittings and outdoor sensor.
	BE141620GEK0032 [1 used]	TRANSFORMER - 120V-24V 20VA with QC's Prod. 50/60Hz
VAV-PWPH4-BSPC-PCBMUA	Size 4 Horizontal Heater VAV Profile and Wiring Package w/ Building Static Pressure Control used with the MUA board.
Show parts
	8164 [100 used]	1/4" Nylon Tubing - Used with the Modular Make-Up Air Units A1-D, A2-D, A3-D, A4-D, A5-D and the NHMUA1, NHMUA2, NHMUA3, AI (Price Per Foot). Type 12.
	69918 [1 used]	3/16" Hose Barb , 1/8" NPT BRASS HOSE BARB FITTING
	A/MLP2-D25-W-B-A-C-0P [1 used]	ACI- MLP2 Series Low Differential Pressure transmitters, pressure range of - .25" w.c. to + .25" w.c. low temperature version. Sensor has brass fittings. Accepts 0.25 O.D. x 0.17 I.D. Push On.
	AFX24SR [1 used]	Damper Actuator, spring return, 2-10 dc siganal, 24vac power supply. Same actuator as AFB24SR with 10ft A3 Cable.
	440097-131280 [1 used]	Female 90 Degree Brass Elbow, Pipe/Thread Size 1/8"
	90108A417 [2 used]	Zinc Plated Steel Type A USS WASHER, 3/8" Screw Size 1" OD, 0.06"-0.11" Thick
VAV-PWPH4-403G	Size 4 Horizontal Heater VAV Profile and Wiring Package w/ CO Detector (by others) Speed Control
Show parts
	NMQX24-MFT [1 used]	ACTUATOR - NM Series Direct Coupled Damper Actuator Non Spring Return, 12va, 70 in-lb torque, 2-10 vdc or 4-20ma control signal. Used on VAV bypass dampers.
	DDP-106-177 [1 used]	AIR FLOW SWITCH - Used with industrial two speed and industrial vav units. Factory set @ .15" to .65".
	S1A [1 used]	Auxiliary end switch for AM, GM, LM, NM series actuators, contains one spdt end switches, 3 amp (0.5a inductive) at 250v rating.
	BE141620GEK0032 [1 used]	TRANSFORMER - 120V-24V 20VA with QC's Prod. 50/60Hz
VAV-PWPH4-CSAI-PCB	Size 4 Horizontal Heater VAV Profile and Wiring Package w/ Constant Speed Control or Analog Input Control PCB
Show parts
	AFX24SR [1 used]	Damper Actuator, spring return, 2-10 dc siganal, 24vac power supply. Same actuator as AFB24SR with 10ft A3 Cable.
VAV-PWPH4-CSAI	Size 4 Horizontal Heater VAV Profile and Wiring Package w/ Constant Speed Control or Analog Input Control
Show parts
	NMQX24-MFT [1 used]	ACTUATOR - NM Series Direct Coupled Damper Actuator Non Spring Return, 12va, 70 in-lb torque, 2-10 vdc or 4-20ma control signal. Used on VAV bypass dampers.
	DDP-106-177 [1 used]	AIR FLOW SWITCH - Used with industrial two speed and industrial vav units. Factory set @ .15" to .65".
	S1A [1 used]	Auxiliary end switch for AM, GM, LM, NM series actuators, contains one spdt end switches, 3 amp (0.5a inductive) at 250v rating.
	BE141620GEK0032 [1 used]	TRANSFORMER - 120V-24V 20VA with QC's Prod. 50/60Hz
VAV-PWPH4-DSPC-PCBMUA	Size 4 Horizontal Heater VAV Profile and Wiring Package w/ Duct Static Pressure Control used with the MUA board.
Show parts
	8164 [100 used]	1/4" Nylon Tubing - Used with the Modular Make-Up Air Units A1-D, A2-D, A3-D, A4-D, A5-D and the NHMUA1, NHMUA2, NHMUA3, AI (Price Per Foot). Type 12.
	69918 [1 used]	3/16" Hose Barb , 1/8" NPT BRASS HOSE BARB FITTING
	A/MLP2-015-W-B-A-C-0P [1 used]	ACI- MLP2 Series Low Differential Pressure transmitters, pressure range of - 15" w.c. to + 15" w.c. low temperature version. Sensor has brass fittings. Accepts 0.25 O.D. x 0.17 I.D. Push On.
	AFX24SR [1 used]	Damper Actuator, spring return, 2-10 dc siganal, 24vac power supply. Same actuator as AFB24SR with 10ft A3 Cable.
	440097-131280 [1 used]	Female 90 Degree Brass Elbow, Pipe/Thread Size 1/8"
	90108A417 [2 used]	Zinc Plated Steel Type A USS WASHER, 3/8" Screw Size 1" OD, 0.06"-0.11" Thick
VAV-PWPH4-M	Size 4 Horizontal Heater VAV Profile and Wiring Package w/ Manual Adjustment
Show parts
	NMQX24-MFT [1 used]	ACTUATOR - NM Series Direct Coupled Damper Actuator Non Spring Return, 12va, 70 in-lb torque, 2-10 vdc or 4-20ma control signal. Used on VAV bypass dampers.
	DDP-106-177 [1 used]	AIR FLOW SWITCH - Used with industrial two speed and industrial vav units. Factory set @ .15" to .65".
	S1A [1 used]	Auxiliary end switch for AM, GM, LM, NM series actuators, contains one spdt end switches, 3 amp (0.5a inductive) at 250v rating.
	BE141620GEK0032 [1 used]	TRANSFORMER - 120V-24V 20VA with QC's Prod. 50/60Hz
VAV-PWPH4-MAN-PCB	Size 4 Horizontal Heater VAV Profile and Wiring Package w/ Manual Control PCB
Show parts
	AFX24SR [1 used]	Damper Actuator, spring return, 2-10 dc siganal, 24vac power supply. Same actuator as AFB24SR with 10ft A3 Cable.
VAV-PWPH4-CSAI	Size 4 Horizontal Heater VAV Profile and Wiring Package w/ Constant Speed Control or Analog Input Control
Show parts
	NMQX24-MFT [1 used]	ACTUATOR - NM Series Direct Coupled Damper Actuator Non Spring Return, 12va, 70 in-lb torque, 2-10 vdc or 4-20ma control signal. Used on VAV bypass dampers.
	DDP-106-177 [1 used]	AIR FLOW SWITCH - Used with industrial two speed and industrial vav units. Factory set @ .15" to .65".
	S1A [1 used]	Auxiliary end switch for AM, GM, LM, NM series actuators, contains one spdt end switches, 3 amp (0.5a inductive) at 250v rating.
	BE141620GEK0032 [1 used]	TRANSFORMER - 120V-24V 20VA with QC's Prod. 50/60Hz
FIRESTAT-DISCHARGE	Discharge Firestat for Heaters Set to 240°F - Old Controls
Show parts
	L4029E1045 [1 used]	DISCHARGE FIRE STAT - High Temperature Limit Switch manual reset, breaks at 240 degrees
FREEZESTAT-	Freezestat factory set at 35°F and 10 minutes.
FRSTAT-20	Freezestat With 20' Sensor. Factory set at 35°F and 10 minutes.
Show parts
	A/CP-DO-240-QC [1 used]	10K, Type II thermistor with 6" probe. 20' wire leads. (Replaces part# A/CP-DO-120-QC)
	00202-0289 [1 used]	Freezestat Control, (30°F to 75°F temperature range and 1min to 10min time range). Factory set at 35°F and 10 minutes. Also Known As Low Temp Sensor. Sensors sold separately, A/CP-DO-240-QC (20') and A/CP-DO-120-QC (10').
FRSTAT-20-LTL	Freezestat With 20' Sensor and Low Temp Light on Remote Panel. Factory set at 35°F and 10 minutes.
Show parts
	A/CP-DO-240-QC [1 used]	10K, Type II thermistor with 6" probe. 20' wire leads. (Replaces part# A/CP-DO-120-QC)
	00202-0289 [1 used]	Freezestat Control, (30°F to 75°F temperature range and 1min to 10min time range). Factory set at 35°F and 10 minutes. Also Known As Low Temp Sensor. Sensors sold separately, A/CP-DO-240-QC (20') and A/CP-DO-120-QC (10').
FRSTAT-20-LTL	Freezestat With 20' Sensor and Low Temp Light on Remote Panel. Factory set at 35°F and 10 minutes.
Show parts
	A/CP-DO-240-QC [1 used]	10K, Type II thermistor with 6" probe. 20' wire leads. (Replaces part# A/CP-DO-120-QC)
	00202-0289 [1 used]	Freezestat Control, (30°F to 75°F temperature range and 1min to 10min time range). Factory set at 35°F and 10 minutes. Also Known As Low Temp Sensor. Sensors sold separately, A/CP-DO-240-QC (20') and A/CP-DO-120-QC (10').
FIRESTAT-INTAKE	Intake Firestat for Heaters Set to 135°F - Old Controls
Show parts
	L4029E1011 [1 used]	INTAKE FIRE STAT - High Temperature Limit Switch used manual reset, breaks at 135 degrees
IBT/DF/RTU Nema 4x remote Space Sensor	Nema 4x Remote Room Sensor Option. Wall Mountable 10k Room Sensor Included.
Show parts
	A/CP-O-4x [1 used]	Room Temperature sensor. Thermistor. NEMA 4X Enclosure. Used with EMSplus & Smart Controls. 10k.
A/CP-D-12"-GD	10k Type 2 Thermistor with 12 Inch Probe
IBT/RTU remote Space Sensor	Remote Room Sensor Option. Wall Mountable 10k Room Sensor Included.
Show parts
	18-8 Plenum Wire [50 used]	18/8 Plenum rated Thermostat wire. 18 Gauge, 8 conductor. Type CMP/CL2P with PVC Insulation jacket. Meets Article 800. Conductor Colors = Black, Red, White, Green, Brown, Blue, Orange, Yellow. Sold by the foot. 250 foot max continuous run. 75°C (167°F) (A0017722)
	A/CP-R2 [1 used]	Room Temperature sensor. Thermistor. Wall mount Enclosure. Used with EMSplus & Smart Controls. 10k.
Blower Delay Stop	Blower Delay Stop. Allows supply fan to run after the burner has shut off Factory set at 90 secs for indirect 30 secs for direct.
PRE-PT	Pre purge (set at 30 seconds) allowing the blower to purge the inside of the heater.
R4VBI	Size 4 Horizontal Industrial Vbank Insulation Upgrade
LOADREACTORININD	Mount Load Reactor in Industrial Mau (Does not include reactor cost, just mounting).
SPVCM	Unit Mount Static Pressure VFD Control (preset to: -0.01 and 0.02)
FMSVI-4	Floor Mounted Spring Vibration Isolators for Industrial Size 4 Heaters and Supply Fans. Cannot be used in conjuction with curb.
Show parts
	SLFC1000 [1 used]	Isolation spring for modular MAU's. 1000lbs resistance, 1.0" rated deflection, floor mounted. Color, Black.
	SLFC1350 [2 used]	Isolation spring for modular MAU's. 1350lbs resistance, 1.0" rated deflection, floor mounted. Color, Yellow.
	SLFC1750 [1 used]	Isolation spring for modular MAU's. 1750lbs resistance, 1.0" rated deflection, floor mounted. Color, Black with Red Inner Spring.
HSVI-4	Hanging Spring Vibration Isolators for Size 4 Industrial Heaters and Supply Fans. Cannot be used in conjunction with curb.

Security Policy		Privacy Policy		Legal Notice		Warranty		Return Policy
Copyright ® 2003-2014 Thermotek All Rights Reserved.