Fan Parts

Home About Us Contact Us Help

Buy Online or Call 1-800-476-5888

Heaters

Exhaust Fans

Make-Up Air

Accessories » Economy Inline Filtered Modular Packaged Unit Rooftop Filtered

Cooling Modules Heating Modules Intake/Discharge Accessories

DUCTWORK

Single Wall Grease Duct Double Wall Grease Duct Chimney Special Gas Vent HVAC Supply Duct

Kitchen Ventilation

HVAC

CASLINK

Resources

DU12HTH Parts

Motors, Pulleys, & Motor Specific Parts

Motor HP Phs Voltage FLA Shaft Frame Weight RPM Vendor

CK42BS04M01-50-115 0.18 1 115 V 2.4 0.5" 9 lbs 1400 HSSA

ODP (Open Drip Proof)

Show parts

SJOOW-143	14/3 SJOOW Cord - OD = .365 - 300V Single Phase Applications. Price per foot.
800041	Bolt Whiz 10-32 X 1/2, SFB103212Z, Steel Grade 5 Minimum (3 Evenly Spaced Radial Marks)
3231	Connector 1/2" Straight - Non Metallic Gray, For Use With SJOOW Cord OD Range .170 To .470. Also used on Residential Hood
810022	Green Ground Screw
Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
58371-1/2	Junction Box - 2 1/8" X 4" X 2 1/16" - Used for mounting Speed Controls and 3 pole switches. 2-1/8" Deep.
TY-224-107-CONNECTOR	Motor Connector - Quick Disconnect Wire Harness With Ground. Used To Connect Direct Drive DU/DR Motors With Six Pin Connectors To The Speed Control. Used For 115/1/60 & 230/1/60 Vac Motors & Speed Controls.
KBWC-16K	Motor Speed Control, Solid State, Model KBWC-16K (H6323), 6 AMPS - 120 V.A.C. @25°C. Factory set to reduce to 65VAC under motor load. (72 VAC with 100 Watt load)
800030	Nut Whiz 10-32, SFLN1032Z, Steel, Large Flange
800023B	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.

CK42BS04M01-50-230 0.18 1 230 V 1.2 0.5" 9 lbs 1400 HSSA

ODP (Open Drip Proof)

Show parts

SJOOW-143	14/3 SJOOW Cord - OD = .365 - 300V Single Phase Applications. Price per foot.
800041	Bolt Whiz 10-32 X 1/2, SFB103212Z, Steel Grade 5 Minimum (3 Evenly Spaced Radial Marks)
3231	Connector 1/2" Straight - Non Metallic Gray, For Use With SJOOW Cord OD Range .170 To .470. Also used on Residential Hood
810022	Green Ground Screw
Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
58371-1/2	Junction Box - 2 1/8" X 4" X 2 1/16" - Used for mounting Speed Controls and 3 pole switches. 2-1/8" Deep.
TY-224-107-CONNECTOR	Motor Connector - Quick Disconnect Wire Harness With Ground. Used To Connect Direct Drive DU/DR Motors With Six Pin Connectors To The Speed Control. Used For 115/1/60 & 230/1/60 Vac Motors & Speed Controls.
KBWC-25K-H6182	Motor Speed Control, Solid State, Model KBWC-25K (H6182), 5 AMPS - 230 V.A.C. @25°C. Factory set to reduce to 130 VAC under motor load. (150 VAC with 100 Watt load). Used On DU/DR 85 HFA.
800030	Nut Whiz 10-32, SFLN1032Z, Steel, Large Flange
800023B	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.

CK42BS04M01-60-115 0.18 1 115 V 1.9 0.5" 10 lbs 1620 HSSA

ODP (Open Drip Proof)

Show parts

SJOOW-143	14/3 SJOOW Cord - OD = .365 - 300V Single Phase Applications. Price per foot.
800041	Bolt Whiz 10-32 X 1/2, SFB103212Z, Steel Grade 5 Minimum (3 Evenly Spaced Radial Marks)
3231	Connector 1/2" Straight - Non Metallic Gray, For Use With SJOOW Cord OD Range .170 To .470. Also used on Residential Hood
810022	Green Ground Screw
Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
58371-1/2	Junction Box - 2 1/8" X 4" X 2 1/16" - Used for mounting Speed Controls and 3 pole switches. 2-1/8" Deep.
TY-224-107-CONNECTOR	Motor Connector - Quick Disconnect Wire Harness With Ground. Used To Connect Direct Drive DU/DR Motors With Six Pin Connectors To The Speed Control. Used For 115/1/60 & 230/1/60 Vac Motors & Speed Controls.
KBWC-16K	Motor Speed Control, Solid State, Model KBWC-16K (H6323), 6 AMPS - 120 V.A.C. @25°C. Factory set to reduce to 65VAC under motor load. (72 VAC with 100 Watt load)
800030	Nut Whiz 10-32, SFLN1032Z, Steel, Large Flange
800023B	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.

CK42BS04M01-60-230 0.18 1 230 V 1 0.5" 9 lbs 1620 HSSA

ODP (Open Drip Proof)

Show parts

SJOOW-143	14/3 SJOOW Cord - OD = .365 - 300V Single Phase Applications. Price per foot.
800041	Bolt Whiz 10-32 X 1/2, SFB103212Z, Steel Grade 5 Minimum (3 Evenly Spaced Radial Marks)
3231	Connector 1/2" Straight - Non Metallic Gray, For Use With SJOOW Cord OD Range .170 To .470. Also used on Residential Hood
810022	Green Ground Screw
Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
58371-1/2	Junction Box - 2 1/8" X 4" X 2 1/16" - Used for mounting Speed Controls and 3 pole switches. 2-1/8" Deep.
TY-224-107-CONNECTOR	Motor Connector - Quick Disconnect Wire Harness With Ground. Used To Connect Direct Drive DU/DR Motors With Six Pin Connectors To The Speed Control. Used For 115/1/60 & 230/1/60 Vac Motors & Speed Controls.
KBWC-23K-H6180	Motor Speed Control, Solid State, Model KBWC-23K (H6180), 2.5 AMPS - 230 V.A.C. @25°C. Factory set to reduce to 130 VAC under motor load. (172 VAC with 100 Watt load). Used On DU/DR30 HFA
800030	Nut Whiz 10-32, SFLN1032Z, Steel, Large Flange
800023B	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.

BMN42-180I1-ES-IBA-CA-60-115 0.25 1 115 V 2.9 0.5" 42 10 lbs 1800 Telco Intercontinental Corp

TEAO-ECM (Totally Enclosed Air Over Electronically Commutated Motor)

Show parts

SJOOW-143	14/3 SJOOW Cord - OD = .365 - 300V Single Phase Applications. Price per foot.
810022	Green Ground Screw
Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
58371-1/2	Junction Box - 2 1/8" X 4" X 2 1/16" - Used for mounting Speed Controls and 3 pole switches. 2-1/8" Deep.
800023B	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.
ECM-Harness-T	Wiring Harness for Telco EC motors. Connects power to speed control and transformer. Used with Telco EC Motors.

BMN42-180I1-ES-IBA-CA-50-115 0.25 1 115 V 2.9 0.5" 42 10 lbs 1800 Telco Intercontinental Corp

TEAO-ECM (Totally Enclosed Air Over Electronically Commutated Motor)

Show parts

SJOOW-143	14/3 SJOOW Cord - OD = .365 - 300V Single Phase Applications. Price per foot.
810022	Green Ground Screw
Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
58371-1/2	Junction Box - 2 1/8" X 4" X 2 1/16" - Used for mounting Speed Controls and 3 pole switches. 2-1/8" Deep.
800023B	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.
ECM-Harness-T	Wiring Harness for Telco EC motors. Connects power to speed control and transformer. Used with Telco EC Motors.

BMN42-180I2-ES-IBA-CA-60-230/277 0.25 1 208-230-277 V 1.9-1.8-1.5 0.5" 42 10 lbs 1800 Telco Intercontinental Corp

TEAO-ECM (Totally Enclosed Air Over Electronically Commutated Motor)

Show parts

SJOOW-143	14/3 SJOOW Cord - OD = .365 - 300V Single Phase Applications. Price per foot.
810022	Green Ground Screw
Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
58371-1/2	Junction Box - 2 1/8" X 4" X 2 1/16" - Used for mounting Speed Controls and 3 pole switches. 2-1/8" Deep.
800023B	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.
ECM-Harness-T	Wiring Harness for Telco EC motors. Connects power to speed control and transformer. Used with Telco EC Motors.

BMN42-180I2-ES-IBA-CA-50-230/277 0.25 1 208-230-277 V 1.9-1.8-1.5 0.5" 42 10 lbs 1800 Telco Intercontinental Corp

TEAO-ECM (Totally Enclosed Air Over Electronically Commutated Motor)

Show parts

SJOOW-143	14/3 SJOOW Cord - OD = .365 - 300V Single Phase Applications. Price per foot.
810022	Green Ground Screw
Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
58371-1/2	Junction Box - 2 1/8" X 4" X 2 1/16" - Used for mounting Speed Controls and 3 pole switches. 2-1/8" Deep.
800023B	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.
ECM-Harness-T	Wiring Harness for Telco EC motors. Connects power to speed control and transformer. Used with Telco EC Motors.

CK42BS04M02-50-115 0.18 1 115 V 2.4 0.5" 42 9 lbs 1400 HSSA

TEFC (Totally Enclosed Fan Cooled)

Show parts

SJOOW-143	14/3 SJOOW Cord - OD = .365 - 300V Single Phase Applications. Price per foot.
800041	Bolt Whiz 10-32 X 1/2, SFB103212Z, Steel Grade 5 Minimum (3 Evenly Spaced Radial Marks)
3231	Connector 1/2" Straight - Non Metallic Gray, For Use With SJOOW Cord OD Range .170 To .470. Also used on Residential Hood
810022	Green Ground Screw
Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
58371-1/2	Junction Box - 2 1/8" X 4" X 2 1/16" - Used for mounting Speed Controls and 3 pole switches. 2-1/8" Deep.
TY-224-107-CONNECTOR	Motor Connector - Quick Disconnect Wire Harness With Ground. Used To Connect Direct Drive DU/DR Motors With Six Pin Connectors To The Speed Control. Used For 115/1/60 & 230/1/60 Vac Motors & Speed Controls.
KBWC-16K	Motor Speed Control, Solid State, Model KBWC-16K (H6323), 6 AMPS - 120 V.A.C. @25°C. Factory set to reduce to 65VAC under motor load. (72 VAC with 100 Watt load)
800030	Nut Whiz 10-32, SFLN1032Z, Steel, Large Flange
800023B	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.

CK42BS04M02-50-230 0.18 1 230 V 1.2 0.5" 42 9 lbs 1400 HSSA

TEFC (Totally Enclosed Fan Cooled)

Show parts

SJOOW-143	14/3 SJOOW Cord - OD = .365 - 300V Single Phase Applications. Price per foot.
800041	Bolt Whiz 10-32 X 1/2, SFB103212Z, Steel Grade 5 Minimum (3 Evenly Spaced Radial Marks)
3231	Connector 1/2" Straight - Non Metallic Gray, For Use With SJOOW Cord OD Range .170 To .470. Also used on Residential Hood
810022	Green Ground Screw
Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
58371-1/2	Junction Box - 2 1/8" X 4" X 2 1/16" - Used for mounting Speed Controls and 3 pole switches. 2-1/8" Deep.
TY-224-107-CONNECTOR	Motor Connector - Quick Disconnect Wire Harness With Ground. Used To Connect Direct Drive DU/DR Motors With Six Pin Connectors To The Speed Control. Used For 115/1/60 & 230/1/60 Vac Motors & Speed Controls.
KBWC-25K-H6182	Motor Speed Control, Solid State, Model KBWC-25K (H6182), 5 AMPS - 230 V.A.C. @25°C. Factory set to reduce to 130 VAC under motor load. (150 VAC with 100 Watt load). Used On DU/DR 85 HFA.
800030	Nut Whiz 10-32, SFLN1032Z, Steel, Large Flange
800023B	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.

CK42BS04M02-60-115 0.18 1 115 V 1.9 0.5" 42 9 lbs 1625 HSSA

TEFC (Totally Enclosed Fan Cooled)

Show parts

SJOOW-143	14/3 SJOOW Cord - OD = .365 - 300V Single Phase Applications. Price per foot.
800041	Bolt Whiz 10-32 X 1/2, SFB103212Z, Steel Grade 5 Minimum (3 Evenly Spaced Radial Marks)
3231	Connector 1/2" Straight - Non Metallic Gray, For Use With SJOOW Cord OD Range .170 To .470. Also used on Residential Hood
810022	Green Ground Screw
Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
58371-1/2	Junction Box - 2 1/8" X 4" X 2 1/16" - Used for mounting Speed Controls and 3 pole switches. 2-1/8" Deep.
TY-224-107-CONNECTOR	Motor Connector - Quick Disconnect Wire Harness With Ground. Used To Connect Direct Drive DU/DR Motors With Six Pin Connectors To The Speed Control. Used For 115/1/60 & 230/1/60 Vac Motors & Speed Controls.
KBWC-16K	Motor Speed Control, Solid State, Model KBWC-16K (H6323), 6 AMPS - 120 V.A.C. @25°C. Factory set to reduce to 65VAC under motor load. (72 VAC with 100 Watt load)
800030	Nut Whiz 10-32, SFLN1032Z, Steel, Large Flange
800023B	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.

CK42BS04M02-60-230 0.18 1 230 V 1 0.5" 42 9 lbs 1625 HSSA

TEFC (Totally Enclosed Fan Cooled)

Show parts

SJOOW-143	14/3 SJOOW Cord - OD = .365 - 300V Single Phase Applications. Price per foot.
800041	Bolt Whiz 10-32 X 1/2, SFB103212Z, Steel Grade 5 Minimum (3 Evenly Spaced Radial Marks)
3231	Connector 1/2" Straight - Non Metallic Gray, For Use With SJOOW Cord OD Range .170 To .470. Also used on Residential Hood
810022	Green Ground Screw
Bushing 7/8	Insulated Snap Bushing - For .875 Hole Diameter.
58371-1/2	Junction Box - 2 1/8" X 4" X 2 1/16" - Used for mounting Speed Controls and 3 pole switches. 2-1/8" Deep.
TY-224-107-CONNECTOR	Motor Connector - Quick Disconnect Wire Harness With Ground. Used To Connect Direct Drive DU/DR Motors With Six Pin Connectors To The Speed Control. Used For 115/1/60 & 230/1/60 Vac Motors & Speed Controls.
KBWC-23K-H6180	Motor Speed Control, Solid State, Model KBWC-23K (H6180), 2.5 AMPS - 230 V.A.C. @25°C. Factory set to reduce to 130 VAC under motor load. (172 VAC with 100 Watt load). Used On DU/DR30 HFA
800030	Nut Whiz 10-32, SFLN1032Z, Steel, Large Flange
800023B	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.

The manufacturer reserves the right to use alternate motors from alternate vendors that meet the operating requirements of the fan but may have slightly different specifications.

Replacement Parts

Part
800034 [4 used]	A0005690 - Nut Whiz 1/4-20, SFLN1420LZ, Steel, Large Flange
0120763.0800 [4 used]	A0031100 - 1"L, 1/4-20 Matpoint, Self Aligning, Hex Head, Grade 5 Bolt
F5061516 [1 used]	Apron 14 3/16" Dia. Out. Bottom X 22" Dia. Ins. Top X 14 1/2" Height, .080 x 32" 1100-0 Alum. For DU12 / DU12FA / DU12RA (Spun) (620326)
F8041516-S [1 used]	Base Assembly For DU12 / DR12
800041 [7 used]	Bolt Whiz 10-32 X 1/2, SFB103212Z, Steel Grade 5 Minimum (3 Evenly Spaced Radial Marks)
F2140014 [1 used]	Cooling Tube 3 1/2" Out. Dia. X 5 7/8" Long, .080 Wall Thk. Extruded Alum. For BDU11, DU12H, DU30 & DU33 (620307)
F2100001 [2 used]	Cooling Tube Grommet 3 1/2" Ins. Dia., 4 1/2" Out. Dia., 3/8" Thk., Black Silicone Rubber(620047)
ETL-Label [1 used]	Label - ETL Information Label. Label located in job docs should be printed and shipped.
MANUAL EXHAUST [1 used]	Manual for PRVs
F5151516-S [1 used]	Motor Cover 14 5/16" Dia. Ins. X .875" Height, .24GA Galv. (Spun) DU12 Pan Hood
800030 [8 used]	Nut Whiz 10-32, SFLN1032Z, Steel, Large Flange
800036 [8 used]	Nut Whiz 8-32, Steel
SB6-4-RIVET [2 used]	RIVET - 3/16" Diameter, .126 To .250 Grip Range, SB6-4 Button Head Steel/Steel. Replaced 800075.
F2051516-S [1 used]	Shaft Wrapper 14 1/4" Dia. Out. X 8 3/4" Height. For DU12
SKID-3237 [1 used]	Skid - 32" X 37" - Used For BDU 11, BDCR 7, 8, 9 & 11, DU/DR 25, 30 & 33.
F5041516-S [1 used]	TOP PLATE, 20GA GALVANIZED, DU/DR 12 F5041516
F8031516-S [4 used]	Vertical Brace Assy. 1" X 7 15/16", 14 Ga. Galv. Steel For DU12 / DR12
F8011516 [1 used]	Wheel Assembly 10 1/2" Dia. Top X 8 1/2" Dia. Ins. Bottom X 4 3/16" Height used on DU, DR 12 DD (620319).

Curbs

Part
CRB17.5X8E	ROOF CURB - 17.5" Square X 8" High
CRB17.5X9E	ROOF CURB - 17.5" Square X 9" High
CRB17.5X12E	ROOF CURB - 17.5" Square X 12" High
CRB17.5X12-BTC	BOLT TOGETHER ROOF CURB - 17.5" Square X 12" High, 18 GA Galvanized. Ships Flat. Pitched Curb Option Not Available with Bolt Together Curbs.
CRB17.5X14E	ROOF CURB - 17.5" Square X 14" High
CRB17.5X16E	Roof Curb 17-1/2" sq. x 16" high
CRB17.5X18E	Roof Curb 17-1/2" sq. x 18" high
CRB17.50X20E	ROOF CURB - 17.50" Square X 20" High
CRB17.5X20E	Roof Curb 17-1/2" sq. x 20" high
CRB17.50X21E	ROOF CURB - 17.50" Square X 21" High
CRB17.5x22E	ROOF CURB - 17.5" Square X 22" High
CRB17.5x24E	ROOF CURB - 17.5" Square X 24" High
CRB17.5x26E	ROOF CURB - 17.5" Square X 26" High
CRB17.5x26L-BTC	BOLT TOGETHER ROOF CURB - 17.5" Square X 26" High, 18 GA Galvanized. Vented. Ships Flat. Pitched Curb Option Not Available with Bolt Together Curbs.
CRB17.5x52E	Roof Curb 17-1/2" sq. x 52" high
CRB17.5x55E	Roof Curb 17-1/2" sq. x 55" high
CRB17.5x61E	Roof Curb 17-1/2" sq. x 61" high

Options

Part
ECM Wiring Package - MSC	ECM Wiring Package - Exhaust - Manual or 0-10VDC Reference Speed Control -MSC- (TELCO), CCW Rotation
Show parts
	CAS MSC [1 used]	Motor Speed Control for EC motors. For use with Nidec and Telco EC motors. Uses 0 to 100% or 0 to 10V speed reference with rpm indication. 24VAC/24VDC input. Controls 4 Pole/1800 RPM motor with PWM input. Includes 0-10VDC input speed reference pins. Part replaces: ECM-VCU-RTC. Controller needs initial programming before shipping from the factory.
MSC w/ 10KLVC-DB	ECM Wiring Package - Exhaust - Manual Potentiometer Speed Control -MSC-
Show parts
	10KLVC-DB [1 used]	10K OHM POTENTIOMETER WITH INTEGRATED WALL PLATE.
	CAS MSC [1 used]	Motor Speed Control for EC motors. For use with Nidec and Telco EC motors. Uses 0 to 100% or 0 to 10V speed reference with rpm indication. 24VAC/24VDC input. Controls 4 Pole/1800 RPM motor with PWM input. Includes 0-10VDC input speed reference pins. Part replaces: ECM-VCU-RTC. Controller needs initial programming before shipping from the factory.
ECM Wiring Package - MSC - MODBUS	ECM Wiring Package - Exhaust - MODBUS Control -MSC- (TELCO), CCW Rotation
Show parts
	CAS MSC [1 used]	Motor Speed Control for EC motors. For use with Nidec and Telco EC motors. Uses 0 to 100% or 0 to 10V speed reference with rpm indication. 24VAC/24VDC input. Controls 4 Pole/1800 RPM motor with PWM input. Includes 0-10VDC input speed reference pins. Part replaces: ECM-VCU-RTC. Controller needs initial programming before shipping from the factory.
ECM Wiring Package-RTC	ECM Wiring Package - Manual or 0-10VDC Reference Speed Control -RTC- (TELCO Motor), CCW Rotation
Show parts
	ECM-VCU-RTC [1 used]	Motor Speed Control for EC motors. For use with Nidec and Telco EC motors. Uses 0 to 100% speed reference with rpm indication. 24VAC input. Controls 4 Pole/1800 RPM motor with PWM input. Includes 0-10VDC input speed reference pins. Part replaces EVO/ECM-VCU-36-MP and EVO/ECM-ACU+S1.1-MP.
ECM Wiring Package-ECPM03	ECM Wiring Package - PWM Signal from ECPMO3 Prewire (TELCO Motor), CCW Rotation
52012	Turn-tite Low-Pressure Mechanical Test Plug Steel W/Neoprene Seal, for Pipe ID 3.75". Used for Upblast Fan Wheel Access. - Cut Hole with McMaster Carr Hole Saw 4066A54 With Pilot Bit 4066A79.
GC-CUF	Grease Cup for kitchen-duty centrifugal exhaust fans, Box Dimensions 17-1/8 L X 5-1/16 W X 3-3/4 H (20 Gauge) (Includes Down Spout)
Show parts
	F2100015 [1 used]	Grease Pipe Down Spout 1 1/2" Ins. Dia., Material Vinyl Color Grey, 60 Durometer For BDU11 Thru BDU36, BDU15HP Thru BDU36HP, DU8 Thru DU85 - 99800PEP.
I 12 BDD w/ 120/240V Motor	MOTORIZED BACK DRAFT DAMPER - with flange, damper is 12" sq. 2" deep, O.D. of flange is 14" sq. Actuator is 120/240V
Show parts
	MTR-611 [1 used]	120/240 v Motor Pack for I Series Backdraft Dampers
	I 12 BDD [1 used]	Gravity Back Draft Damper - with flange, damper is 12" sq. 2" deep, O.D. of flange is 14" sq.
I 12 BDD w/ 24V Motor	MOTORIZED BACK DRAFT DAMPER - with flange, damper is 12" sq. 2" deep, O.D. of flange is 14" sq. Actuator is 24V
Show parts
	MTR-611 24V [1 used]	24 V Motor Pack for I Series Backdraft Dampers
	I 12 BDD [1 used]	Gravity Back Draft Damper - with flange, damper is 12" sq. 2" deep, O.D. of flange is 14" sq.
WALLMOUNT 18.5"SQ x 2"	Wall Mount Bracket - 18.5" square x 2" for fans with 19" square base and with 13" centered square hole.
WALLMOUNT 18.5"SQ x 5"	Wall Mount Bracket - 18.5" square x 5" for fans with 19" square base, with 13" centered square hole. Used when gravity damper is ordered.
WBE-10-36	Windband Extension Assembly for Centrifigual Upblast Fan with 10.50" Wheel. 23.760" OD, 36" Height. Constructed of Galvanized Steel After 1/1/2016. Includes 3 Quick Release latches & 10 Self Drilling Screws.
Show parts
	800032 [3 used]	A0005688 - Zinc-Plated Grade 5 Steel Serrated-Flange Locknut, 3/8"-16 Thread Size, 7/8" Large Flange Diameter, 11/32" Overall Height
	F2370012 [2 used]	Angle Ring 1/8" X 1" X 1" Aluminum Angle, 22 1/8" Dia. Out. For DU 12 (620364)
	92323A558 [3 used]	Bolt Whiz 3/8-16 X 1 1/2, Steel Grade 5 Minimum (3 Evenly Spaced Radial Marks)
	SB6-4-RIVET [21 used]	RIVET - 3/16" Diameter, .126 To .250 Grip Range, SB6-4 Button Head Steel/Steel. Replaced 800075.
	800023B [10 used]	Self Drilling Screw 1/4-14 X 1 1/4", with rubber washer, drill & tap HWBS.
	97-60-320-11 [3 used]	Southco large draw latch for windband extensions
	F2161012WBE-36-S [1 used]	Windband Extension - 36" Height, .24GA Galv. For DU 12 Centrifugal Upblast (Direct Drive) Exhaust Fan. Sheet Metal Piece ONLY.
FAN HEAT BAFFLE	Insulated Heat Baffle for Exhaust Fans. Type 475FRK 1 inch thick insulation installed on the top side of the top plate and under the motor of upblast and downblast fans. Cut to fit shaft wrapper and around vibration isolators and motor cooling hole. Caulked down to top plate.
Show parts
	INSULATION/sq ft [3 used]	INSULATION (Price per Sq Foot)
HD-HBKIT-LOCKING	HINGE KIT - Heavy Duty Hinge kit with locking spring pin for exhaust fan roof curbs. Includes Hardware to attach hinge to curb and hinge to base. 10 GA Galvanized. Note: Requires 16GA curb or 18GA curb with 16GA back plate - (9"x9" cut size).
Show parts
	800034 [44 used]	A0005690 - Nut Whiz 1/4-20, SFLN1420LZ, Steel, Large Flange
	0120763.0800 [44 used]	A0031100 - 1"L, 1/4-20 Matpoint, Self Aligning, Hex Head, Grade 5 Bolt
	910XH [1 used]	HINGE KIT - Heavy Duty Hinge kit with locking spring pin for exhaust fan roof curbs. 10 GA Galvanized.
HBKIT-01	HINGE KIT - Standard Hinge kit for exhaust fan roof curbs. Includes Hardware to attach hinge to curb and hinge to base. Ships Loose. Used on Fans with wheels 20 inches or smaller. 12 GA Galvanized.
Show parts
	800032 [6 used]	A0005688 - Zinc-Plated Grade 5 Steel Serrated-Flange Locknut, 3/8"-16 Thread Size, 7/8" Large Flange Diameter, 11/32" Overall Height
	31817 [30 used]	Self Drilling Screw - 12 - 14 X 3/4" - Steel, Zinc Coated - Used To Mount Hinge Kits.
F2051516-CS	Shaft Wrapper 14 1/4" Dia. Out. X 7 3/4" Height. For DU12 when used on concession stands. Low Profile Shaft Wrapper.
MIAMI-DADE NOA-1 Aluminum Upblast	Miami Dade Impact and Wind Load Certification +150 / -150 PSF - Miami Dade County Product Control Approved. Florida Building Code approval. Roof & Wall Mount Exhaust Curbs up to 20" high must be 20 gauge Aluminized. Roof & Wall Mount Exhaust Curbs above 20" high up to 42" high must be 18 Gauge Aluminized.
Hinge Kit Label	Label - Remove The Hinge Kit Label From The Fan Base.
F2361516	Bird Screen - 1/2" X 1/2" (3 3/4" X 46") Wire Screen for Direct Drive Upblast/Downblast Fans (850030) DU/DR12, Galv after welded wire cloth.
Ship Loose Disconnect For Remote Mount	Disconnect Switch Loose - Wire Is Extended 10' To Allow Remote Mounting Of The NEMA 3R Enclosure & Switch. Cord Fittings Are Installed In Switch Box. 10-32 Hardware and 7/8" Plug Are Installed In Apron Switch Mounting Holes.
Show parts
	9750K25-APRON-PLUG [1 used]	Apron Plug - Push-in Flexible Round Plastic Plug, Fits 7/8" ID, 1-5/32" Head Diameter
	800041 [2 used]	Bolt Whiz 10-32 X 1/2, SFB103212Z, Steel Grade 5 Minimum (3 Evenly Spaced Radial Marks)
	800030 [2 used]	Nut Whiz 10-32, SFLN1032Z, Steel, Large Flange
2E340	Line Voltage Thermostat, 120 or 240 volt, used as fan thermostat in cooling applications. Close on temperature rise. 80-130 degree dial. 2E340. 13.8 amps at 120V, 10 amps at 240V.
Through Wall Curb Mount	Through Wall Curb Mount Installation Option.
I 12 BDD	Gravity Back Draft Damper - with flange, damper is 12" sq. 2" deep, O.D. of flange is 14" sq.
Dry Mode Exhaust	Current Sensor Mounted In Exhaust Fan For Use With Pool Room Temp Control
Show parts
	A/MCS-A [1 used]	Current Sensor - Solid Core, AC Current Range: 0.32 - 150A , NO Contact w/ Max Rating of 1A @ 36VAC/VDC
Full Crating for Exhaust Fan	Full crating for exhaust fans for shipping.
EPO11-Enamel	Tan Enamel Coating For 11" or smaller Fan. Consult factory for other colors. Sherwin Williams p/n F75KXN5809-4347, (AX = A0006229) Color: SW2353. Adds two weeks to the lead time of unit.
MS100W	Occupancy Sensor, White, 120VAC. 1/2HP, 9 Amp Max (Fan +Light). 300W max LED, 600W max Incandescent. Fits single-gang box.

Security Policy		Privacy Policy		Legal Notice		Warranty		Return Policy
Copyright ® 2003-2014 Thermotek All Rights Reserved.